Author Topic: Chainsaw bar mounts  (Read 755 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 3908
  • Karma: 141
  • OHIO REDNECK
REDNECK Saw Repair

Share on Facebook Share on Twitter


Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 66
  • Information collector
  • Location: Troms, North Norway
Re: Chainsaw bar mounts
« Reply #1 on: January 24, 2014, 07:11:07 am »
There is at least one important mistake there - the site states the larger Husky Mount (D009) is 9.5 mm, while it is 9 mm (nominal that is of course).

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 215
  • Magnesium and Iron.
  • Location: Northern California.
Re: Chainsaw bar mounts
« Reply #2 on: January 25, 2014, 04:06:29 pm »
There is at least one important mistake there - the site states the larger Husky Mount (D009) is 9.5 mm, while it is 9 mm (nominal that is of course).

Yep.  That's the one that's caused the most confusion so far.  There are also several 'blanks' that really need to be filled by somebody who has old Oregon, Windsor, Sandvik, General, Cannon, etc bar catalogs.  Still a great resource however.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21042
  • Karma: 468
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Chainsaw bar mounts
« Reply #3 on: January 25, 2014, 04:11:59 pm »
Be nice to see the mistakes fixed with info that has been sent with right info etc.  Shame some folks took the time to do so and it is just sweep under the carpet. Not me.

Like to see the whole chainsaw area updated too with more saws.

Just me hoping and wont ever happen. Better then nothing I guess.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
2 Replies
491 Views
Last post January 01, 2012, 10:45:23 pm
by scott kunz
1 Replies
475 Views
Last post September 14, 2013, 12:13:31 pm
by Cut4fun .
20 Replies
2071 Views
Last post September 07, 2016, 10:25:58 pm
by Al Smith
10 Replies
244 Views
Last post October 10, 2014, 06:31:47 pm
by mnmdad
4 Replies
101 Views
Last post October 15, 2014, 03:39:36 pm
by aclarke
11 Replies
364 Views
Last post November 08, 2014, 10:27:28 pm
by Eccentric
8 Replies
467 Views
Last post December 27, 2014, 12:06:22 pm
by Eccentric
0 Replies
158 Views
Last post January 05, 2015, 07:23:39 pm
by silverman1
6 Replies
200 Views
Last post April 07, 2015, 06:09:08 am
by Spike60
5 Replies
179 Views
Last post April 24, 2019, 07:28:52 pm
by Cut4fun .