« previous next »
Pages: 1 2 [3]   Go Down

Author Topic: Honing ball Hone etc  (Read 2564 times)

0 Members and 2 Guests are viewing this topic.

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2106
  • Karma: 171
  • Location: MD
Re: Honing ball Hone etc
« Reply #20 on: December 21, 2017, 09:29:56 pm »
Where are you getting them from. Sounds like they work well. Have a few cylinders I could try it out on.
Logged
FEAR NO TREE. FEAR GOD.
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23511
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Honing ball Hone etc
« Reply #21 on: December 21, 2017, 10:11:58 pm »
Quote from: jmester on December 21, 2017, 09:29:56 pm
Where are you getting them from. Sounds like they work well. Have a few cylinders I could try it out on.

Got mine from pmd or something like that on amazon. baileys sell them too and even as a set. But I refuse to buy anything from them.
 http://www.brushresearch.com/product-line.php?line=1&utm_source=AdRoll&utm_medium=banner&utm_campaign=FH
Logged

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181
Re: Honing ball Hone etc
« Reply #22 on: December 22, 2017, 06:25:46 am »
 ;) I fired Baileys also for various reasons.Ball hones aren't that hard to find though .However keep in mind they won't round out or remove taper .Only a precision hone will do that .Then again most saw cylinders are plated and it's really a moot point .
Logged
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23511
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Honing ball Hone etc
« Reply #23 on: April 03, 2018, 02:16:20 pm »
Just want to show what a difference finishing touch of cross hatching does. ;)

First 2 pics.
Here is cleaned up by hand with emery cloth and flapper wheel.  See how you can still see the scuff area. But it is smooth as can be to go across it with fingernail or finger or whatever you want to use.

Then the next 2 pics are after the final step with ball hone  used for crosshatch.    :P


Logged
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23511
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Honing ball Hone etc
« Reply #24 on: May 07, 2018, 05:07:53 pm »
Any you guys using the SC ones?  They sent me a 240SC instead of the 240AO 57mm one.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23511
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Honing ball Hone etc
« Reply #25 on: May 02, 2021, 09:32:40 am »
The 046 D cylinder

Showing crosshatching to deglaze. Could run just like it is. But I like fresh crosshatch with new rings.

Before and after



Logged
Like Like x 1 View List
Pages: 1 2 [3]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
3 Replies
625 Views 		Last post February 02, 2012, 08:31:26 pm
by North West Farmer
8 Replies
605 Views 		Last post January 03, 2013, 06:42:14 pm
by Al Smith
5 Replies
607 Views 		Last post December 19, 2013, 09:10:40 am
by doreadeal
1 Replies
319 Views 		Last post September 21, 2015, 09:17:20 pm
by 660magnum
9 Replies
1199 Views 		Last post January 17, 2016, 11:12:18 pm
by Chris-PA
1 Replies
552 Views 		Last post March 03, 2018, 09:19:29 am
by Cut4fun .