« previous next »
Pages: 1 [2]   Go Down

Author Topic: How to test the coil in a two piece trigger/coil ignition setup  (Read 6654 times)

0 Members and 0 Guests are viewing this topic.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: How to test the coil in a two piece trigger/coil ignition setup
« Reply #10 on: January 28, 2016, 11:34:41 pm »
Ignition system testing . . .

This does not talk about testing the coil itself. It came from the Dolmar 340/420 service manual. This saw had a single piece coil setup.

With the present day single piece coil pointless ignitions . . .

Accurate testing of the ignition module is only possible with sophisticated test equipment.

For this reason it is only necessary to carry out a spark test in the workshop.

A new ignition module must be installed if no ignition spark is obtained (after checking that wiring and stop switch are in good condition).
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: How to test the coil in a two piece trigger/coil ignition setup
« Reply #11 on: January 28, 2016, 11:55:41 pm »
With the old points type ignitions here are some typical parameters . . .  This is for an old Stihl 010

Condenser value .17 uf

Coil primary resistance .8 -1.3 ohms
coil secondary resistance 7.2K - 8.8K ohms

Point gap .012" - .016"

23 - 24 degress BTDC

Spark plug gap .020" - .025"

Coil to flywheel gap is the thickness of an appointment or plain business card - about .010"

Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline gregh

  • 3 cube
  • *
  • Posts: 11
  • Karma: 0
Re: How to test the coil in a two piece trigger/coil ignition setup
« Reply #12 on: March 27, 2016, 01:48:26 pm »
I have a home lite brush utter xl, that has a magneto and points as a peice part, and it won't fire. I set the points to .015 and still won't fire.


Mower Tech small engine repair
Joplin, mo
Logged
Pages: 1 [2]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
0 Replies
1102 Views 		Last post March 15, 2012, 08:37:50 pm
by mweba
3 Replies
1651 Views 		Last post January 31, 2013, 09:18:08 am
by Al Smith
2 Replies
1311 Views 		Last post March 05, 2013, 04:37:21 am
by pete
0 Replies
574 Views 		Last post December 04, 2013, 07:38:06 pm
by SELLSEVERYTHING
3 Replies
1287 Views 		Last post December 09, 2013, 10:59:02 pm
by mortalitool
1 Replies
757 Views 		Last post June 02, 2014, 11:08:00 am
by mowertech
2 Replies
1206 Views 		Last post January 09, 2014, 03:10:57 pm
by tommysp61
3 Replies
1037 Views 		Last post January 13, 2014, 08:15:53 pm
by KilliansRedLeo
2 Replies
1255 Views 		Last post January 22, 2014, 07:13:30 pm
by 660magnum
8 Replies
1463 Views 		Last post October 07, 2014, 02:36:40 pm
by sharkey