Author Topic: 066 on a 064 question (Read 1624 times)

SDB777 · « **Reply #10 on:** January 20, 2014, 07:11:54 pm »

Quote from: blsnelling on January 19, 2014, 10:09:02 pm

Yes, a 066/660 topend can be installed on a 064. As already mentioned, you have to slot the holes in the 066 cylinder base. Use the 064 cylinder gasket as a template. Enlarging the holes in the case to 6mm is a good idea, but is not required. It's easy enough to do.

Think I just watched a video on YouTube done by you....same username?

https://www.youtube.com/watch?v=pN3w2e5UI0M

Scott (very nice) B

SDB777 · « **Reply #11 on:** January 23, 2014, 07:28:51 am »

Spent almost an hour before being called to dinner by the wife, and was not able to get the muffler off this saw. Even sprayed the WD40 onto them rusted pieces! Re sprayed them and left it sitting so that the WD might make its way to whatever is holding them in place?

First guess is this saw has never been apart?
If they don't let go, any tips to keep from breaking stuff?

Scott (things gotta get easier) B

660magnum · « **Reply #12 on:** January 23, 2014, 11:13:49 am »

mdavlee . · « **Reply #13 on:** January 23, 2014, 04:13:53 pm »

Run the saw for a minute and then break the bolts loose if you don't want to use a small torch to heat it up.

SDB777 · « **Reply #14 on:** January 23, 2014, 05:53:38 pm »

Thanks for the tip. I will give that a go tomorrow morning...it will be to late to do it after work tonite.

Scott (chainsawin' in the dark is bad) B

sharkey · « **Reply #15 on:** January 23, 2014, 06:44:27 pm »

Heat is definitely your friend when working with saws. It makes getting the bearings and cranks into and out of the cases manageable. If you dont want to use a torch, you can use a heat gun, hair dryer or even a flood lamp.

Enjoyed reading through your site. Great looking blanks and was impressed with your acrylic work too.

SDB777 · « **Reply #16 on:** January 24, 2014, 06:27:17 am »

Quote from: sharkey on January 23, 2014, 06:44:27 pm

Heat is definitely your friend when working with saws. It makes getting the bearings and cranks into and out of the cases manageable. If you dont want to use a torch, you can use a heat gun, hair dryer or even a flood lamp.

Enjoyed reading through your site. Great looking blanks and was impressed with your acrylic work too.

Thanks, was wondering what everyone used when the saw was disassembled for any length of time as far as heat goes(not like you could start it up and let it 'self-generate' heat).

And thanks for looking through the website....sometimes a fella gets lucky finding local timber. The Acrylics is all the wife, she has the timing and eye for color combos!

Scott (seems it cold out there this mornin') B

man of stihl · « **Reply #17 on:** January 24, 2014, 09:00:45 am »

If it were me I would just replace the piston (if needed) and rings. The 64 is a great saw and I don't know if you can feel a power difference by adding the 66 top end. So I don't think its worth the extra work. I have owned both BTW. So I'm not just making assumptions.

Tractorsaw1 · « **Reply #18 on:** January 29, 2014, 03:10:18 pm »

Has anyone used any of the mako cylinder kits? Anyone done any port work on the mako kit? 4 years ago I moved the base screws out & opened them up to 6mm. Cut 10-15 cord a year with the saw & then the aftermarket piston gave up the ghost, so I am ready for a different top end & cylinder.

Subject / Started by	Replies	Last post
034 super question? Started by riverrocket Stihl	1 Replies 316 Views	December 24, 2012, 05:30:19 am by Al Smith
Bar and Chain Question Started by darren_palms « 1 2 » Husqvarna	14 Replies 588 Views	January 26, 2013, 01:38:18 pm by mdavlee .
009 carb linkage question Started by nortryder Stihl	1 Replies 337 Views	March 31, 2013, 09:51:03 pm by Remington
2159 bogging question Started by Vance in AK « 1 2 » Jonsered	12 Replies 1071 Views	September 25, 2013, 09:27:52 pm by Vance in AK
038 piston question Started by Sintersis Stihl	6 Replies 420 Views	October 16, 2013, 04:50:13 pm by Al Smith
I know it's a stupid question -- can't get flywheel off pro mac 10-10 Started by strad « 1 2 » McCulloch	18 Replies 1432 Views	October 27, 2013, 09:26:23 pm by 660magnum
Craftsman 3.7 Piston Question Started by roostersgt Poulan	8 Replies 512 Views	January 20, 2014, 06:57:42 pm by roostersgt
Stupid impulse hose installation question Started by jon1270 « 1 2 » Stihl	10 Replies 687 Views	September 06, 2014, 07:00:15 pm by Fish
help/question Started by mrbb Poulan	3 Replies 275 Views	September 30, 2014, 05:52:33 pm by mrbb
Quick question about starter switch Started by newfonfire Stihl	2 Replies 285 Views	January 27, 2015, 03:51:19 pm by Fish

Chainsaw Repair

News:

Author Topic: 066 on a 064 question (Read 1624 times)

SDB777

Re: 066 on a 064 question

SDB777

Re: 066 on a 064 question

660magnum

Re: 066 on a 064 question

mdavlee .

Re: 066 on a 064 question

SDB777

Re: 066 on a 064 question

sharkey

Re: 066 on a 064 question

SDB777

Re: 066 on a 064 question

man of stihl

Re: 066 on a 064 question

Tractorsaw1

Re: 066 on a 064 question

Related Topics