« previous next »
Pages: [1]   Go Down

Author Topic: MS 390 - HT Lead info required  (Read 250 times)

0 Members and 0 Guests are viewing this topic.

Offline Le Maisonniau

  • 3 cube
  • *
  • Posts: 14
  • Karma: 2
  • Location: France
MS 390 - HT Lead info required
« on: May 12, 2013, 01:50:31 am »
Hi,
I have just joined this forum - I am looking for some assistance with my MS390.

I managed to pull the cover and connector off the HT lead whilst doing routine servicing, I have replaced it  >:(, but cannot get the m/c to start, I suspect the hole in the side/end of the lead is now too great for a good connection.
The lead is the 5mm type with a weird pin that pushes through into the HT lead and then the rubber cover is slid over!!.

I have purchased a length of new 5mm HT lead from a Stihl agent in France.

Is it possible that you could PM me a diagram from the SM that will show me how to replace the HT lead.  (i.e where to connect the opposite end to plug connection)  I have user manual and IPL.


Kind regards
John (Retired in France with 6 acres of woodland to "play" with) ;D
Logged
Retired in France

Share on Facebook Share on Twitter

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23520
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: MS 390 - HT Lead info required
« Reply #1 on: May 12, 2013, 10:04:02 am »
I wouldnt think you would need a new lead. But you do have center the metal L pin  you call it in the core of the wire to make contact.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23520
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: MS 390 - HT Lead info required
« Reply #2 on: May 12, 2013, 10:08:12 am »
PM'ing you the whole stihl ms290 ms310 ms390 service manual to look at and save. 
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
49 Replies
16448 Views 		Last post February 13, 2016, 06:19:32 pm
by farmboy
4 Replies
373 Views 		Last post May 22, 2013, 02:37:04 pm
by Le Maisonniau
1 Replies
184 Views 		Last post February 07, 2014, 06:08:57 pm
by KilliansRedLeo
5 Replies
518 Views 		Last post April 13, 2014, 11:22:26 am
by KilliansRedLeo
4 Replies
329 Views 		Last post June 18, 2014, 08:50:07 am
by pete
6 Replies
575 Views 		Last post November 07, 2014, 08:44:37 pm
by farmboy
2 Replies
686 Views 		Last post August 22, 2015, 10:26:29 am
by 1manband
5 Replies
351 Views 		Last post March 30, 2017, 07:32:36 pm
by fossil
4 Replies
576 Views 		Last post August 13, 2017, 01:48:48 pm
by Cut4fun .
3 Replies
635 Views 		Last post February 06, 2018, 05:43:16 pm
by jmester