Author Topic: Broken Bar Stud 039  (Read 280 times)

0 Members and 0 Guests are viewing this topic.

Offline BSW

  • 3 cube
  • *
  • Posts: 7
  • Karma: 0
Broken Bar Stud 039
« on: February 16, 2014, 08:11:06 am »
Have a rear broken bar stud on a 039 and the repair shop told me he has little success getting them turned out because they are installed into plastic with lock tight. He's probabley more interested in selling me a new saw but I don't see that much of a issue with drilling and using an ez out on it but concerned with the threads. Any thoughts or advice! Bryan

Share on Facebook Share on Twitter


Offline Fish

  • Piped Saw
  • *****
  • Posts: 309
  • Karma: 39
Re: Broken Bar Stud 039
« Reply #1 on: February 16, 2014, 10:56:12 am »
He is wrong, the rear bar stud is threaded into the metal bottom engine pan.

Offline Fish

  • Piped Saw
  • *****
  • Posts: 309
  • Karma: 39
Re: Broken Bar Stud 039
« Reply #2 on: February 16, 2014, 11:00:36 am »
Yes, the older saws, they really used some serious Loctite, would probably just be easier to remove the block, and get a good used engine pan, most of the guys here probably have a bunch laying around they would part with.

Online jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2047
  • Karma: 157
  • Location: MD
Re: Broken Bar Stud 039
« Reply #3 on: February 16, 2014, 12:55:08 pm »
I have a couple of engine pans around if you are interested in one. where did the stud break flush at the engine pan or is there still some sticking out of the case?
FEAR NO TREE. FEAR GOD.

Offline BSW

  • 3 cube
  • *
  • Posts: 7
  • Karma: 0
Re: Broken Bar Stud 039
« Reply #4 on: February 16, 2014, 07:22:33 pm »
Flush with the engine pan.

Online jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2047
  • Karma: 157
  • Location: MD
Re: Broken Bar Stud 039
« Reply #5 on: February 16, 2014, 07:31:09 pm »
If you pull the motor out you can try and drill it and use an easy out. If you go that route when you are ready to use the easy out apply some heat to the area where the studs is to help release the loc tite. If that does not work out for you. Let me know I have a used engine pan I would be willing to get rid of. If you are interested in the pan pm me. May save you a bunch of time to just replace the pan as fish stated earlier.
FEAR NO TREE. FEAR GOD.

Offline BSW

  • 3 cube
  • *
  • Posts: 7
  • Karma: 0
Re: Broken Bar Stud 039
« Reply #6 on: February 16, 2014, 07:34:38 pm »
Bought the saw in 1990 and have used it with no major breakdowns and have replaced the chain drive sprocket 4 times and countless chains and a couple of bars over the years. Jump the gun and bought a new one but am not replacing the 039 it's still has a lot of miles left! But not gonna rest until it's fixed. U can't have to many saws can u!?

Offline BSW

  • 3 cube
  • *
  • Posts: 7
  • Karma: 0
Re: Broken Bar Stud 039
« Reply #7 on: February 16, 2014, 07:42:51 pm »
Should I disassemble the saw or try and drill  and use an ez out like it is?

Offline mountainlake

  • 5 cube
  • ***
  • Posts: 119
  • Karma: 21
Re: Broken Bar Stud 039
« Reply #8 on: February 17, 2014, 05:31:08 am »
 
 If screwed into metal a little heat makes those loctited  bolts come out easy. Steve

Offline BSW

  • 3 cube
  • *
  • Posts: 7
  • Karma: 0
Re: Broken Bar Stud 039
« Reply #9 on: February 17, 2014, 07:44:25 am »
I'm gonna try and extract it and will let u know how it goes, thanks for the info guys and jmester I my have to hit u up on a engine pan depending how it goes! Thanks Again Bryan

 

Related Topics

  Subject / Started by Replies Last post
stihl bar stud repair

Started by mweba « 1 2 » Stihl

12 Replies
2697 Views
Last post September 09, 2019, 09:42:41 am
by joe_indi
3 Replies
190 Views
Last post August 17, 2013, 10:20:27 pm
by cowroy
6 Replies
305 Views
Last post April 29, 2014, 07:51:55 pm
by Cut4fun .
5 Replies
586 Views
Last post September 03, 2014, 11:53:37 pm
by 3000 FPS
7 Replies
302 Views
Last post September 02, 2014, 03:29:39 pm
by Nathaniel Vansickle
4 Replies
137 Views
Last post April 03, 2015, 09:25:53 am
by wild262
1 Replies
218 Views
Last post January 25, 2016, 11:21:00 am
by srcarr52
2 Replies
333 Views
Last post August 20, 2016, 12:56:41 pm
by jr27236
0 Replies
92 Views
Last post December 20, 2016, 06:35:52 pm
by fisaw
0 Replies
82 Views
Last post September 09, 2019, 09:38:40 am
by joe_indi