« previous next »
Pages: [1]   Go Down

Author Topic: Cylinders need work  (Read 1192 times)

0 Members and 0 Guests are viewing this topic.

Offline dpjones

  • 5 cube
  • ***
  • Posts: 131
  • Karma: 18
Cylinders need work
« on: October 04, 2017, 07:31:07 pm »
I have bought five aftermarket cylinder kits this year for my saws, one was Cross Performance for a 660, one was Hyway for Husky 350, one was Farmertec, and the other two were just no name  Chinese. All of them needed work, the Hyway had keepers for a bigger piston pin. Hyway and Cross were prettier but still needed work.

My question is are the OEM ready to bolt on? or do they need work too? Not talking about porting, just a stock build.

Maybe dumb question but I still want to know.
Thanks
DJ
Logged

Share on Bluesky Share on Facebook

Useful Useful x 1 View List

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC
Re: Cylinders need work
« Reply #1 on: October 04, 2017, 07:39:06 pm »
I have never had an OEM PC kit that needed work to install.  Somebody else may but I haven't.
Shep
Logged
Agree Agree x 1 View List

Offline dpjones

  • 5 cube
  • ***
  • Posts: 131
  • Karma: 18
Re: Cylinders need work
« Reply #2 on: October 04, 2017, 07:46:52 pm »
Well I was just wondering, I would have thought the cross and hyway wouldn't and they may could have been used but I didn't want to. Ports around were the rings travel were rough.
DJ
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24232
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Cylinders need work
« Reply #3 on: October 04, 2017, 08:13:46 pm »
stock oem never had to do anything

wont use other rings unless oem or caber. Only time I try other afm rings or circlips is testing in my own saws.  Otherwise oem circlips too.
Logged

Offline sharkey

  • Piped Saw
  • *****
  • Posts: 368
  • Karma: 37
Re: Cylinders need work
« Reply #4 on: October 13, 2017, 03:05:19 am »
I just put a top end, oem P&C kit on an Echo 670.  The kit came with the rings, pin, circlips, a bearing and a gasket.  Went on toot sweet.  Rebuilt the carb and on its way it went.  Nothing extra needed.   
Logged

Offline trappermike

  • 5 cube
  • ***
  • Posts: 129
  • Karma: 17
  • 40 years mechanical and 2-Stroke racing experience
  • Location: British Columbia, Canada
Re: Cylinders need work
« Reply #5 on: January 05, 2019, 05:15:51 pm »
A friend of mine was building a hot 460 Stihl,wanted my help and had a new aftermarket piston and cyl.,I'd never saw one of these before but wow,the ports were really badly cast,terrible,it took more work just to clean them up that the actual porting work. Probably fine for a stock replacement,but I agree,I would not risk cheap rings,I would replace them with factory.
Logged
Experience builds real horsepower...
When the hammer drops the BS stops:Loggers sports competition!
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
9 Replies
3755 Views 		Last post February 02, 2022, 10:20:52 am
by 3000 FPS
20 Replies
4204 Views 		Last post November 09, 2012, 06:23:19 am
by Al Smith
3 Replies
939 Views 		Last post September 01, 2013, 03:08:12 pm
by 660magnum
15 Replies
1653 Views 		Last post March 24, 2014, 10:28:17 am
by brokenbudget
17 Replies
2419 Views 		Last post January 26, 2014, 09:59:09 am
by Cut4fun .
6 Replies
2453 Views 		Last post February 20, 2014, 07:38:22 pm
by Al Smith
4 Replies
960 Views 		Last post February 21, 2018, 11:37:27 am
by Cut4fun .
2 Replies
1632 Views 		Last post March 02, 2015, 02:39:45 pm
by Cut4fun .
14 Replies
3198 Views 		Last post May 10, 2019, 06:39:19 am
by Al Smith
2 Replies
1073 Views 		Last post March 22, 2022, 08:23:11 am
by joe_indi