Author Topic: high idles then dies...  (Read 319 times)

0 Members and 0 Guests are viewing this topic.

Offline R.Singletary

  • 4 cube
  • **
  • Posts: 30
  • Karma: 1
high idles then dies...
« on: June 09, 2014, 09:42:29 pm »
Hello, i have a stihl 051 av, when i start it, it idles ok, but then it takes off and high idle  for about 10 seconds then dies. I have tryed to ajust the carb and it still dose it. i think its an air leak, but not sure where. i really want to get this saw running, but not too use, its too big and its a classic...HELP....

Share on Facebook Share on Twitter


Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: high idles then dies...
« Reply #1 on: June 09, 2014, 10:01:55 pm »
Check the fuel vent first

Offline R.Singletary

  • 4 cube
  • **
  • Posts: 30
  • Karma: 1
Re: high idles then dies...
« Reply #2 on: June 09, 2014, 10:16:21 pm »
How would i do that and where is it on a stihl? is it in the same place as on a husky? in the fule tank?

Offline RoyM

  • Gas Hotsaw
  • ******
  • Posts: 502
  • Karma: 45
  • Location: Surrey British Columbia
Re: high idles then dies...
« Reply #3 on: June 09, 2014, 10:54:31 pm »
Near as I remember, the tank vent is a short piece of tubing with a screw in it sticking out of the tank. The lay downs suffered from air leaks around the intake gaskets. Also make sure the insulator block is not ****.
Old age and treachery always overcome youth and enthusiasm

Offline Fish

  • Piped Saw
  • *****
  • Posts: 309
  • Karma: 39
Re: high idles then dies...
« Reply #4 on: June 10, 2014, 03:40:40 pm »
Go through the fuel system correctly, that old beast deserves to be fixed correctly!!!

Pull and rebuild the carb, check all hoses, connections, gaskets on all of the blocks between the carb and block, impulse.
But before buying anything, after you have the carb off, go ahead and pull the muffler and look at your piston condition, that will
tell you your next step.
When you have the carb apart, you will likely see a wad of snuff in the screen, that would be the remains of your fuel filter insert,
so you will need a new fuel filter, remove the spring/lever/needle, and hold the bare carb body up to a light and peek through that passage, then blow it out with some air, then look again, and visually verify that it is clear, then blow out the other crud, and rebuild with a new kit.

Looking for air leaks is one of the last things to be doing..........

Offline R.Singletary

  • 4 cube
  • **
  • Posts: 30
  • Karma: 1
Re: high idles then dies...
« Reply #5 on: June 12, 2014, 10:02:14 pm »
Hello, i would like to thank aclarke,Roym and Fish...thank you so much for the imput. I will kit the carb in a couple of week and let the forum know how it goes. In the mean time, i did pull the carb apart and the screen did have white residue . i blew it clean with air and then pulled the needle and made sure there was blockage, then looked thru it for a visual. then i put it back together. thats when it started the high idle. Thank you for your help. i will update in a couple of  weeks....

Offline Oliver1655

  • 3 cube
  • *
  • Posts: 21
  • Karma: 2
  • Location: Centarl Missouri
Re: high idles then dies...
« Reply #6 on: December 01, 2014, 11:00:41 pm »
To clarify Roy's post.  The screw/set screw in the tubing style of vent is pushed in about 3-4 threads, NOT screwed in.  If it is screwed in  the treads will cut into the tubing creating a seal loosing the venting ability.  I found this out the hard way on my 08s.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: high idles then dies...
« Reply #7 on: December 01, 2014, 11:04:56 pm »
After making my new vent, I checked it with the MityVac for proper operation. It was A-OK
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

 

Related Topics

  Subject / Started by Replies Last post
17 Replies
718 Views
Last post February 12, 2013, 07:48:58 am
by bassman
9 Replies
477 Views
Last post October 26, 2013, 10:25:33 pm
by 660magnum
21 Replies
796 Views
Last post April 11, 2014, 08:58:12 pm
by 3000 FPS
7 Replies
458 Views
Last post October 29, 2014, 03:58:59 pm
by Fish
2 Replies
176 Views
Last post November 24, 2014, 08:54:41 am
by sharkey
6 Replies
319 Views
Last post February 27, 2015, 02:12:00 pm
by adriandwor
16 Replies
864 Views
Last post October 25, 2015, 09:19:53 pm
by mikehonda
6 Replies
1721 Views
Last post January 08, 2016, 07:31:28 am
by 67L36Driver
1 Replies
143 Views
Last post December 01, 2015, 11:24:23 pm
by Cut4fun .
2 Replies
113 Views
Last post August 17, 2019, 10:53:09 pm
by Midpines