Author Topic: I wasn't looking for another 026 but one found me  (Read 845 times)

0 Members and 0 Guests are viewing this topic.

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2753
  • Karma: 170
Re: I wasn't looking for another 026 but one found me
« Reply #20 on: January 29, 2013, 08:43:49 pm »
I go through Chesterville a couple times a year going over to Mt Vernon .

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: I wasn't looking for another 026 but one found me
« Reply #21 on: January 29, 2013, 08:53:05 pm »
That's Willie

Yep have horse traded with him a couple times.   He is signed up here.  ;)
REDNECK Saw Repair Getter Done

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: I wasn't looking for another 026 but one found me
« Reply #22 on: January 29, 2013, 09:33:05 pm »
I've sold him a model airplane and a few years later a nice four stroke model engine.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline H 2 H

  • 5 cube
  • ***
  • Posts: 100
  • Karma: 11
  • Location: Were the Pacific Northwest Soft Woods Grow
My 26 muff mod... ;)

Here is the MM I ended up with



I just keep making it bigger till I like it :)

I went into it three times since I got it back together making the ports wider :)

 



I'm trying a .325 8 now I was was running a .325 7 rim; just trying to figure out what works best

"People ask me where all my money went, I tell them half of it I spent on gambling, fast women and liquor, the other half I wasted!" W.C.

"..... nothing more funnier than watching some ole coot make a fool out of himself, especially sideways”

"You can't argue with someone that doesn't have any real life experience on the subject."

Offline H 2 H

  • 5 cube
  • ***
  • Posts: 100
  • Karma: 11
  • Location: Were the Pacific Northwest Soft Woods Grow
Things that were replaced

Piston and rings
Crank bearings and seals
All rubber hoses plus intake boot
Fuel filter and I just cleaned oil filter
Carb
Replaced the gaskets in the fuel cap and oil cap
Changed to the metal mess air filter
Changed the bar oilier to a adjustable oilier

Also the saw was put thru the dish washer (don't tell anyone)
"People ask me where all my money went, I tell them half of it I spent on gambling, fast women and liquor, the other half I wasted!" W.C.

"..... nothing more funnier than watching some ole coot make a fool out of himself, especially sideways”

"You can't argue with someone that doesn't have any real life experience on the subject."

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
I've been known to put saw parts in the dish washer too.. ;)
Ron

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2753
  • Karma: 170
Bradley David used to stick saw parts in the dish washer .Lawdy if I did that Mrs Smith would have a fit .

Now what I have done is tote them off to work and use the high temp parts washer . The E-Coat Stihl uses will stand up to but regular paint will melt right off after about a hour in that thing .The water is pushing 190 degrees .

 

Related Topics

  Subject / Started by Replies Last post
21 Replies
828 Views
Last post October 10, 2012, 10:50:38 am
by yldflight
8 Replies
424 Views
Last post August 08, 2013, 11:11:17 pm
by dutchsawdoctor
1 Replies
165 Views
Last post November 05, 2013, 12:38:23 am
by Eccentric