Author Topic: more power MS250 stihl  (Read 7899 times)

0 Members and 15 Guests are viewing this topic.

Offline splitter2784

  • 3 cube
  • *
  • Posts: 17
  • Karma: 1

  • Total Badges: 11
    Badges: (View All)
    Level 3 Second year Anniversary 10 Posts One year Anniversary Level 2 Karma
more power MS250 stihl
« on: July 22, 2014, 09:21:54 pm »
I'm a new guy on the site, I like the information on here I read. I have 2 ms 250's I'd like to try to take one of them and get a little more giddy up and go. I know the standard bore size is 42.5mm. I haven't seen a big bore kit available for this engine any place I have looked.Is there one made and if so and where? I'm old school I don't have any experience tearing a saw down but I am going to do it on this one saw I have. For starters I want to know If I can swap a jug and piston from a ms 260 to a ms 250 block? Will this bolt up or do I need to stick to the same engine families in order for jug swaps to work from one block or engine family to another?  I know the ms 250 is of the 1123 engine family and is the biggest bore of that series and a 250 jug would bolt up to a 230 or any engine in that family. My curiosity is killing me on this I would deeply appreciate any in put on this subject and get me steered in the right direction. I'm not looking for a racer just a good dependable 250 with just a little more power. Thank you

Share on Facebook Share on Twitter


Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

  • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: more power
« Reply #1 on: July 22, 2014, 09:53:59 pm »
The 42.5 mm is the biggest you can go with that family. The engine is a clamshell design with the cylinder and the upper half of the crankcase as one piece. Not a whole lot you can do with them. Most of the 025/MS250 is plastic with a metal engine unit sandwiched inside.

The 026/MS260 is a engine with a separate cylinder and crankcase. The crankcase serves as part of the frame of the whole chainsaw.

The MS250 responds well to opening up the muffler (Muffler Mod), Installing a WT215 Walbro carb ($22.45) but with most of them you will also need a tank vent/needle valve guide to match the WT215 with it's needle valves close together. Most MS250's came from the factory with a Zama carb with the High speed needle at the back of the carb and the low speed needle down low at the front of the carburetor.

Most of the aftermarket flocked air filters are very restrictive. You can get a aftermarket nylon mesh filter that lets them breathe better.

In spite of the MS250 normally coming with a 18" bar, .325 / .063 chain, I like the 16" bar with Stihl RS chisel (Yellow) chain.

Set up this way, they are a pretty hot little limbing saw.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline splitter2784

  • 3 cube
  • *
  • Posts: 17
  • Karma: 1

  • Total Badges: 11
    Badges: (View All)
    Level 3 Second year Anniversary 10 Posts One year Anniversary Level 2 Karma
Re: more power MS250 stihl
« Reply #2 on: July 23, 2014, 07:47:58 pm »
Thank you for the reply. What is the needle valve guide?  Why I was wanting to know about the 260 was the 44mm piston it is just a fuze bigger than the 250's. Thought there might be a possibility of a jug swap. And also I have noticed china made jugs, pistons and overhaul kits are very cheap. Are these good quality replacement parts or have people been haveing problems with them.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

  • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: more power MS250 stihl
« Reply #3 on: July 23, 2014, 08:20:09 pm »
Thank you for the reply. What is the needle valve guide?  Why I was wanting to know about the 260 was the 44mm piston it is just a fuze bigger than the 250's. Thought there might be a possibility of a jug swap. And also I have noticed china made jugs, pistons and overhaul kits are very cheap. Are these good quality replacement parts or have people been having problems with them.

The 260 is made different. the 250 does not have a jug as such. There is no way they will fit each other.

China made jugs are hit and miss. You cannot depend on the quality and even if they are the best, they never get better than genuine OEM. Hyway brand seems the most consistent.

The needle valve guide is a rubber piece that fits over the three adjustment screws on the side of the carburetor to the outlet holes on the outside of the chainsaw.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline splitter2784

  • 3 cube
  • *
  • Posts: 17
  • Karma: 1

  • Total Badges: 11
    Badges: (View All)
    Level 3 Second year Anniversary 10 Posts One year Anniversary Level 2 Karma
Re: more power MS250 stihl
« Reply #4 on: July 23, 2014, 10:09:23 pm »
Ok, thank you very much for the input, I appreciate it

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

  • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: more power MS250 stihl
« Reply #5 on: July 23, 2014, 10:58:05 pm »
To mod the muffler . . .

Remove the muffler from the engine by removing the two nuts.

Lift the spark screen cover from the muffler.

There is a rectangle depression in the main muffler body underneath the spark screen.

This depression typically has a 12mm hole in it. Open the hole up with a round and rectangle file to be as big as the flat part of the depression.

On the side of the muffler body that fastens to the engine, there is a cage in there with several 5mm holes. Open up all these to a larger size that you can.

Be sure to remove all the metal filings from the muffler by washing and blowing it out with a air hose.

Re-install the muffler with the bolts first, then the shield, gasket, muffler, cover, and nuts.

You must re-tune the carb with the mesh air filter and air filter cover installed.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

 

Related Topics

  Subject / Started by Replies Last post
0 Replies
512 Views
Last post February 19, 2012, 04:35:39 pm
by Cut4fun .
Stihl MS250 C

Started by Cut4fun . « 1 2 » Stihl

15 Replies
1370 Views
Last post October 12, 2012, 10:17:35 pm
by Al Smith
MS250 & 026

Started by Vance in AK « 1 2 » Stihl

16 Replies
1234 Views
Last post April 23, 2013, 07:53:23 pm
by Al Smith
Stihl MS250

Started by Cut4fun . « 1 2 3 4 » Stihl

36 Replies
1711 Views
Last post August 13, 2013, 04:38:06 pm
by Cut4fun .
3 Replies
397 Views
Last post September 21, 2013, 03:37:03 pm
by Al Smith
4 Replies
516 Views
Last post October 29, 2013, 05:01:05 pm
by Fish
ms250 questions

Started by countryhog « 1 2 » Stihl

10 Replies
896 Views
Last post January 22, 2014, 01:48:58 pm
by H 2 H
2 Replies
1742 Views
Last post May 22, 2017, 02:50:56 pm
by Cut4fun .
7 Replies
946 Views
Last post February 11, 2019, 01:06:48 pm
by Cut4fun .
6 Replies
976 Views
Last post January 07, 2021, 05:36:09 am
by Dave12