Author Topic: ms 310 topend rebulit  (Read 161 times)

0 Members and 0 Guests are viewing this topic.

Offline northern boy

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
  • its cold up here eh!!
  • Location: ontario canada
ms 310 topend rebulit
« on: January 06, 2014, 02:40:57 pm »
hey guys new to the form looks like a great site need some help just got a ms310 used    put half a dozen cuts on it and it ran alittle fun so took it to the local shop to get get it tuned up and the piston and cylinder r shot should I replace the bearings and oil seals well doing the job i'm up in Canada not sure where to get parts any advice will be great thanks  ???

Share on Facebook Share on Twitter


Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: ms 310 topend rebulit
« Reply #1 on: January 06, 2014, 02:59:55 pm »
Put a 390 engine unit in it? The same one fits the 290, 310, and 390.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline northern boy

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
  • its cold up here eh!!
  • Location: ontario canada
Re: ms 310 topend rebulit
« Reply #2 on: January 06, 2014, 03:11:59 pm »
k ill look in it thanks 660

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: ms 310 topend rebulit
« Reply #3 on: January 06, 2014, 03:19:03 pm »
the carbs are the same on all those.

I don't know a good Canadian source but Ebay is full of after market engine units. They seem to hold up pretty well.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline northern boy

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
  • its cold up here eh!!
  • Location: ontario canada
Re: ms 310 topend rebulit
« Reply #4 on: January 06, 2014, 03:20:09 pm »
will the carb set up be the same as the 310
 ???

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: ms 310 topend rebulit
« Reply #5 on: January 06, 2014, 03:20:39 pm »
yes
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22580
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: ms 310 topend rebulit
« Reply #6 on: January 06, 2014, 03:21:10 pm »
Here is what 660 is talking about  I think.   http://www.baileysonline.com/Chainsaws/Chainsaw-Parts/Short-Blocks/Shindaiwa/NWP-49mm-Short-Block-Cylinder-for-Stihl-Chainsaws-029-039-MS290-MS310-MS390.axd

Suppose to be bolt in ready to go.

Click on stihl board and look down a few threads where someone used one on a 290 build to 390.
REDNECK Saw Repair Getter Done

Offline northern boy

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
  • its cold up here eh!!
  • Location: ontario canada
Re: ms 310 topend rebulit
« Reply #7 on: January 06, 2014, 03:22:24 pm »
k once again thanks ill take a look how much should it cost don't want to get screwed 

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22580
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: ms 310 topend rebulit
« Reply #8 on: January 06, 2014, 03:23:04 pm »
posted above your last post.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
2 Replies
362 Views
Last post May 03, 2013, 06:59:36 am
by Spike60
13 Replies
483 Views
Last post August 14, 2013, 05:41:17 pm
by Cut4fun .
2 Replies
58 Views
Last post August 20, 2014, 11:50:25 pm
by stihls066
2 Replies
170 Views
Last post August 23, 2014, 06:13:55 pm
by Old Iron Logging
14 Replies
470 Views
Last post January 21, 2015, 08:32:45 pm
by Cut4fun .