Author Topic: Stihl bar stud fix  (Read 19462 times)

0 Members and 10 Guests are viewing this topic.

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55

  • Total Badges: 32
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Stihl bar stud fix
« on: March 12, 2012, 10:25:59 pm »
Looking for suggestions.  Only issue with this saw is the bar studs.  One was an attempted heli coil repair and the other is hogged out past that point.  Any tricks from the experienced Stihl guys???  Admittedly my experience is limited.


Bar stud by mweba1, on Flickr

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23706
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: MS 440 bar stud repair
« Reply #1 on: March 13, 2012, 06:37:15 am »
There is a bar stud repair kit offered by stihl that I remember reading about years back. Something about being over sized where they go into the case. I cant remember specifics sorry


other ideas   http://www.mcmaster.com/#threaded-inserts/=gn5tfy

more info  bar stud from an 056 MAG is 10mm and only it had the 10mm studs where they go into the case. 1115-664-2405  $7

stihl over size for 029 etc. So they must have for the mag crankcases too.

If the Standard Collar Screw is part #1127 664 2400, DG 8 thread, use Oversize Collar Screw part # 1127 664 2410, DG 9 thread, for 1127 series saws such as MS 290, MS 390
Installation:
If the thread has been stripped, the damaged mounting hole in the engine housing already has the required diameter (approx. 8 mm) and does not
need to be drilled out. Coat the DG 9 thread of the new collar screw with Red LOCKTITE 262, or equivalent and apply it squarely to the bar mounting face.
Use an 8 mm stud puller to install the collar screw into the engine housing and tighten down to a torque of 16 Nm.

If the Standard Collar Screw is 1123 664 2400, DG 8, use Oversize Collar Screw 1123 664 2405, DG 9, for 1123 series saws (021, 023, 025, MS 210, MS 250). It will also work on the 1130 (MS 170, MS180), and 1132 (MS 191T)
install same as above.

An oversize collar screw, part number 1115 664 2405, is available for alloy housings that have been stripped. The damaged hole will need to be drilled out to 8.5 mm (0.335” or letter drill Q) and rethreaded with a 10 mm by 1.5 pitch tap. Coat the threads with Red LOCKTITE 262, or equivalent, and install with the stud remover or use the double nut method. This collar screw is for the 3003 bar mount.

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55

  • Total Badges: 32
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: MS 440 bar stud repair
« Reply #2 on: March 13, 2012, 08:20:04 am »
Thanks for that info!  I have several 029 and 056 mag II.  One should have a stud left.  Will keep this one updated

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55

  • Total Badges: 32
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: MS 440 bar stud repair
« Reply #3 on: March 13, 2012, 06:53:22 pm »
The 056 mag stud couldn't have worked better.  It cut new threads into the case without issue.  Red lock tight and it should be good for years to come. 
Winner Winner x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23706
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: MS 440 bar stud repair
« Reply #4 on: March 13, 2012, 07:58:30 pm »
Sweet.  8)

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4666
  • Karma: 216
  • OHIO REDNECK

  • Total Badges: 44
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 7 Seventh year Anniversary Apple User
Re: Stihl oversize bar stud replacement
« Reply #5 on: February 05, 2017, 12:57:25 pm »
Just looking for a place to save this pic and info. Stihl oversize bar stud replacements. 
Thanks to a stihl dealer in my other group. ;)



Like Like x 1 View List

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171

  • Total Badges: 31
    Badges: (View All)
    Level 6 Sixth year Anniversary Fifth year Anniversary 1000 Posts Fourth year Anniversary 500 Posts
Re: MS 440 bar stud repair
« Reply #6 on: February 05, 2017, 05:28:40 pm »
Nice
Agree Agree x 1 View List

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2117
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming

  • Total Badges: 37
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: MS 440 bar stud repair
« Reply #7 on: February 06, 2017, 06:24:37 am »
Good stuff.

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2106
  • Karma: 171
  • Location: MD

  • Total Badges: 36
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 6
Re: MS 440 bar stud repair
« Reply #8 on: February 06, 2017, 09:57:43 pm »
Thanks for posting. That should come in handy one day. I knew of the oversized studs for the plastic cased saws. Never knew there was one for mag case saws.
FEAR NO TREE. FEAR GOD.

Offline pete

  • Gas Hotsaw
  • ******
  • Posts: 500
  • Karma: 37

  • Total Badges: 25
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Level 5 Sixth year Anniversary
Re: MS 440 bar stud repair
« Reply #9 on: February 07, 2017, 03:22:37 am »
Any Idea if there is something similar to use on the mag crankcase of an 015 its a ripper of a running powerhead way to good to part out but the stud thread is not great.

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
537 Views
Last post August 17, 2013, 10:20:27 pm
by cowroy
0 Replies
423 Views
Last post December 26, 2013, 09:27:16 am
by jsbirsette6715
0 Replies
735 Views
Last post December 26, 2013, 09:50:16 am
by Cut4fun .
Broken Bar Stud 039

Started by BSW « 1 2 » Stihl

11 Replies
982 Views
Last post February 23, 2014, 04:08:33 am
by bustedknuckles
5 Replies
1095 Views
Last post September 03, 2014, 11:53:37 pm
by 3000 FPS
7 Replies
908 Views
Last post September 02, 2014, 03:29:39 pm
by Nathaniel Vansickle
4 Replies
622 Views
Last post April 03, 2015, 09:25:53 am
by wild262
3 Replies
776 Views
Last post February 21, 2017, 07:52:38 am
by mowertech
0 Replies
464 Views
Last post September 09, 2019, 09:38:40 am
by joe_indi
1 Replies
282 Views
Last post December 25, 2021, 07:53:33 am
by Cut4fun