Author Topic: stihl bar stud repair  (Read 4247 times)

0 Members and 1 Guest are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22581
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: MS 440 bar stud repair
« Reply #10 on: February 07, 2017, 01:42:46 pm »
Thanks for posting. That should come in handy one day. I knew of the oversized studs for the plastic cased saws. Never knew there was one for mag case saws.

My Chainsaw Repair group has over 11,000 members now. Just branched it off of this place not long ago as the websites seem so old school for the millennials today.   Updated Sept 2019 with ovr 38,000 members now.

There are so many stihl techs there and a few of them are moderators.  They share bits and pieces of stuff and it gets lost quickly there. So If I catch it I try and save the good stuff here so not to get lost.  ;)
REDNECK Saw Repair Getter Done

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4334
  • Karma: 189
  • OHIO REDNECK
Re: stihl 461 460 046 290 310 390 029 039 stud repair
« Reply #11 on: September 09, 2019, 08:42:33 am »
@joe_indi  info you shared on the chainsaw repair group earlier. Making sure to save that type of stuff here to find easier later.

Joe
Conversation Starter 4 hrs

I had tried all kinds of fixes for the stripped thread on the crankcase for the 8mm studs on Stihl saws, especially the countless 460s and 461s that are in use here.

But all of them were cumbersome fixes, time consuming and could cause disasters on the crankcase.

That is, until I read a Stihl technical information on an oversize stud for the 29/39 saws.

Self threading 9mm studs on the side that goes into the body. 8mm on the outside.

But these were intended for the non metal housings of the 29/39/290/390 saws. They also had wider collars unsuitable for the use I had in mind.

Anyway in 2001 I got myself a pack of 10 of these oversize studs. Got a friendly tooling shop to reshape them on the lathe. And they worked like a dream!

And I have been using this fix ever since. Time for the fix is just 10 minutes or less.

REDNECK Saw Repair

Offline joe_indi

  • 5 cube
  • ***
  • Posts: 98
  • Karma: 31
  • Location: Cochin, India
Re: stihl bar stud repair
« Reply #12 on: September 09, 2019, 09:42:41 am »
posted is as a new thread here a few minutes ago
Useful Useful x 1 View List

 

Related Topics

  Subject / Started by Replies Last post
12 Replies
1084 Views
Last post January 22, 2012, 01:02:43 pm
by peppone
29 Replies
2854 Views
Last post October 07, 2012, 04:54:28 am
by Drf255
7 Replies
406 Views
Last post December 25, 2012, 01:40:35 pm
by JOE.G
20 Replies
563 Views
Last post August 11, 2013, 08:00:42 am
by pete
3 Replies
226 Views
Last post August 17, 2013, 10:20:27 pm
by cowroy
1 Replies
20 Views
Last post December 30, 2013, 02:26:52 pm
by 660magnum
4 Replies
45 Views
Last post January 19, 2014, 10:23:11 am
by Cut4fun .
Broken Bar Stud 039

Started by BSW « 1 2 » Stihl

11 Replies
349 Views
Last post February 23, 2014, 04:08:33 am
by bustedknuckles
7 Replies
379 Views
Last post September 02, 2014, 03:29:39 pm
by Nathaniel Vansickle
0 Replies
225 Views
Last post September 09, 2019, 09:38:40 am
by joe_indi