« previous next »
Pages: [1]   Go Down

Author Topic: ms170 oiler  (Read 1069 times)

0 Members and 0 Guests are viewing this topic.

Offline bigd74

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0
ms170 oiler
« on: January 11, 2012, 08:48:09 pm »
does anyone have the measurements for setting the oiler depth on an ms170?
Logged

Share on Facebook Share on Twitter

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4141
  • Karma: 175
  • OHIO REDNECK
Re: ms170 oiler
« Reply #1 on: January 12, 2012, 01:09:06 pm »
Never been into one of these MS170 saws. Are you asking do they have adjustable oiler or how to adjust oiler?
Logged
REDNECK Saw Repair

Offline bigd74

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0
Re: ms170 oiler
« Reply #2 on: January 12, 2012, 05:05:38 pm »
their oiler just pushes into a hole but it has to be in just the right amount to far no oil to little no oil and it has to be oriented the correct way apparently stihl makes a special tool to install these but from what i heard its cheaper to have a shop do it than to buy the tool if they'll sell it to you.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22196
  • Karma: 564
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: ms170 oiler
« Reply #3 on: January 12, 2012, 05:24:23 pm »
Let me check the service manual if I have it.

Hopefully someone else knows before I get done reading.

I just looked at the 017 service manual. I dont see anything hard or needing special tools. 017 was saw before MS170.

I'm going to send you the service manual to your email listed here. You take a look at the step by step instructions.
Logged
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22196
  • Karma: 564
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: ms170 oiler
« Reply #4 on: January 12, 2012, 05:37:14 pm »
017 018 work shop manual sent just now to your email.
Logged
REDNECK Saw Repair Getter Done

Offline bigd74

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0
Re: ms170 oiler
« Reply #5 on: January 12, 2012, 06:29:53 pm »
thanks for the manual the tool they have there for pulling and installing limits how far in the pump goes the discharge hole for the pump is abou an 1/8" diameter and has to line up with the same size hole in the case if you miss that at all you get little to no oil on your bar.i may have to try and buy that tool
Logged

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82
Re: ms170 oiler
« Reply #6 on: January 12, 2012, 07:31:52 pm »
Do you have a part # for the tool?
Logged

Offline bigd74

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0
Re: ms170 oiler
« Reply #7 on: January 12, 2012, 08:18:14 pm »
there are three parts to it the assembly tool #1123 890 2200 the puller #1130 893 1400 and the installer #1130 893 1500                                                                                                                                                                                         
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
4 Replies
757 Views 		Last post April 19, 2011, 05:08:32 am
by Al Smith
4 Replies
724 Views 		Last post October 09, 2011, 01:23:47 pm
by Al Smith
0 Replies
1071 Views 		Last post April 04, 2012, 12:29:54 pm
by Cut4fun
ms170

Started by leec Stihl

4 Replies
219 Views 		Last post September 19, 2013, 10:54:14 pm
by leec
ms170 ws manual

Started by leec « 1 2 3 » Stihl

21 Replies
399 Views 		Last post December 15, 2013, 07:57:49 am
by leec
1 Replies
220 Views 		Last post October 29, 2013, 07:26:02 pm
by 660magnum
7 Replies
1159 Views 		Last post April 08, 2017, 05:46:56 am
by brokenbudget
5 Replies
586 Views 		Last post January 19, 2017, 09:55:19 pm
by farmboy
1 Replies
211 Views 		Last post January 30, 2018, 02:02:49 pm
by Cut4fun .
1 Replies
86 Views 		Last post February 03, 2019, 04:32:09 pm
by Cut4fun .