Author Topic: MS192TC just won't stay running  (Read 729 times)

0 Members and 0 Guests are viewing this topic.

Offline crankincraig

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
Re: MS192TC just won't stay running
« Reply #10 on: November 13, 2013, 12:59:15 pm »
Thanks Killians , I would have to say no for sure on fuel line and pinched wire. I went to youtube and there are some videos of saws there that had the same symptoms as mine is having , it definatly goes dead on a lean condition. When it dies out if I choke it it restarts no problem.

 Have not had time to get back to it yet , busy week but maybe thats good to take a break from it. I will vacuum test for bad seals when I get back to it.
 
Thanks again for the suggestions.

Offline Adirondackstihl

  • 6 cube
  • ****
  • Posts: 176
  • Karma: 8
  • Location: Champlain, NY
Re: MS192TC just won't stay running
« Reply #11 on: November 13, 2013, 01:44:33 pm »
I'm guessing crank seal or engine pan leak  ;)

Offline crankincraig

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
Re: MS192TC just won't stay running
« Reply #12 on: November 13, 2013, 02:11:55 pm »
Thanks Adarondack , My guess also at this point. There is nothing else left as far as I can see. Wish I had checked when I had engine out of the old case before I put it all back together. This saw has so little time on it that I never even gave it a second thought.

 Oh well , too late now to change that. Going to give it a break for a couple days and then get back at it.

Thanks to everyone here for all the help and suggestions. I will post an update when I get it straightened out , hope it might help the next guy with a simalar problem.

Offline crankincraig

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
Re: MS192TC just won't stay running
« Reply #13 on: November 15, 2013, 08:03:10 am »
Got it. Crankshaft seal on the clutch side.

Starts easier , carb adjustments now working like they should and it just keeps running.

Guess I really learned a lot from this expierence.

Thanks again for everyones help and suggestions.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: MS192TC just won't stay running
« Reply #14 on: November 15, 2013, 08:33:35 am »
Good that you found and fixed your problem
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: MS192TC just won't stay running
« Reply #15 on: November 23, 2013, 10:20:13 am »
The 192 is definitely the worst Stihl product to work on. Every job no matter how small takes over an hour. So, now that you have a 192 under your belt all the rest of the saws will be cake! ;D

P.S. I hate to see 015, 020 and 192 saws darken the doorway to my shop. LOL
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: MS192TC just won't stay running
« Reply #16 on: November 23, 2013, 10:41:59 am »
One other thing, did you check to see if it is oiling? If the oiler isn't working you get to tear the saw completely apart to replace the oiler. No joke big PITA!
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline crankincraig

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
Re: MS192TC just won't stay running
« Reply #17 on: November 25, 2013, 01:09:47 pm »
Oh yeah . Oiler working fine , actually puts out more than I would have thought. More than my old 019T if I remember correctly. Thanks again for the help guys.

 

Related Topics

  Subject / Started by Replies Last post
4 Replies
1219 Views
Last post February 21, 2012, 09:43:13 am
by mweba
5 Replies
377 Views
Last post November 18, 2012, 10:50:17 am
by Cut4fun .
5 Replies
202 Views
Last post October 03, 2013, 11:51:34 am
by 660magnum
108 Replies
1416 Views
Last post March 07, 2014, 10:47:29 am
by KilliansRedLeo
2 Replies
329 Views
Last post April 23, 2014, 06:31:10 pm
by Jason K
4 Replies
228 Views
Last post June 20, 2014, 09:24:30 am
by Fish
16 Replies
790 Views
Last post January 27, 2017, 04:35:28 pm
by Fishinmech24
6 Replies
1019 Views
Last post July 05, 2016, 09:33:48 am
by Cut4fun .
2 Replies
274 Views
Last post July 04, 2018, 08:14:36 am
by Cut4fun .
2 Replies
166 Views
Last post August 31, 2018, 10:10:01 am
by Cut4fun .