Author Topic: ms211 carb  (Read 113 times)

0 Members and 0 Guests are viewing this topic.

Offline bzs

  • pruner
  • *
  • Posts: 3
  • Karma: 0
ms211 carb
« on: October 23, 2017, 05:31:16 pm »
been trying to adjust the carb on ms211 went to see what the factory settings are it says on the high setting to turn screw cc till stop if I do this the screw end up in my hand ???

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21880
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: ms211 carb
« Reply #1 on: October 23, 2017, 07:18:14 pm »
Yep the one I did dont have a stop either.  Try 1.5 turns out from lightly seated.  You have a tach to fine tune? If not tune by ear fat and listen to clean up in cut.
REDNECK Saw Repair Getter Done

Offline bzs

  • pruner
  • *
  • Posts: 3
  • Karma: 0
Re: ms211 carb
« Reply #2 on: October 26, 2017, 07:44:50 am »
thank you very much how about the low side

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21880
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: ms211 carb
« Reply #3 on: October 26, 2017, 08:01:54 am »
thank you very much how about the low side

I dont recall where I ended up. But you will know. Start at 1 or 1.5 out and fine tune. You want no lag in throttle response.   Once you have that set for quick blips you may need to adjust your I idle some.  Good Luck

or just start adjust L from where it is at. Thats what I did on last one.
REDNECK Saw Repair Getter Done

Offline bzs

  • pruner
  • *
  • Posts: 3
  • Karma: 0
Re: ms211 carb
« Reply #4 on: October 26, 2017, 02:20:39 pm »
thank you very much the manual instructions are very confusing

 

Related Topics

  Subject / Started by Replies Last post
11 Replies
621 Views
Last post March 09, 2011, 02:02:13 pm
by Old Iron Logging
2 Replies
187 Views
Last post November 08, 2013, 05:50:01 am
by sharkey
2 Replies
349 Views
Last post November 18, 2013, 08:45:26 pm
by rayvil01
68 Replies
1983 Views
Last post August 01, 2016, 10:02:15 pm
by 3000 FPS
35 Replies
1067 Views
Last post November 11, 2016, 11:28:35 pm
by pete
ms211

Started by Harvester Stihl

3 Replies
68 Views
Last post January 23, 2015, 11:21:20 pm
by 660magnum
3 Replies
270 Views
Last post June 30, 2015, 07:11:44 pm
by Jason K
5 Replies
241 Views
Last post February 21, 2016, 09:42:40 am
by jmester
MS211

Started by ChipsAhoy Stihl

7 Replies
117 Views
Last post June 20, 2017, 05:41:48 pm
by ChipsAhoy
MS211

Started by ChipsAhoy Stihl

2 Replies
96 Views
Last post December 03, 2017, 09:53:10 am
by ChipsAhoy