Author Topic: ms660  (Read 233 times)

0 Members and 0 Guests are viewing this topic.

Offline don5477

  • 4 cube
  • **
  • Posts: 54
  • Karma: 2
ms660
« on: December 27, 2013, 05:41:13 pm »
can anyone tell me what would be blowing my pull starter pawls,clip and real apart, the real  pawls clip are aftermarket are they just that much junk or could it be something with the fan shroud it's self,the saw is a 064 crank case with a 660 crank,polymer flywheel and top end

Share on Facebook Share on Twitter


Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171
Re: ms660
« Reply #1 on: December 27, 2013, 05:50:34 pm »
It may be aftermarket junk or there's something in a bind. Check to make sure it's not rubbing on something in there. 

Offline don5477

  • 4 cube
  • **
  • Posts: 54
  • Karma: 2
Re: ms660
« Reply #2 on: December 27, 2013, 06:12:16 pm »
this is the 3rd set of aftermarket it blow apart

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2046
  • Karma: 156
  • Location: MD
Re: ms660
« Reply #3 on: December 27, 2013, 08:03:43 pm »
Try putting some grease on the rotor axle (sprocket tip grease)  I would have to say that if it is your third am set that has went bad, I would be trying an oe set. But like gatekeeper said check for some thing binding up on you. Also make sure the spring clip is not bent or deformed. If it falls off there is nothing else to hold it together.
FEAR NO TREE. FEAR GOD.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: ms660
« Reply #4 on: December 27, 2013, 10:07:06 pm »
I had a prob with 066 recoil once.  When you install everything before putting on saw. Are you testing. Pull rope quick with recoil off and see if pawls pop out and then go back in smoothly and quickly when you let rope retract.
REDNECK Saw Repair Getter Done

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2046
  • Karma: 156
  • Location: MD
Re: ms660
« Reply #5 on: December 27, 2013, 11:56:11 pm »
Agreed with cut make sure the pawls expand and contract like they should. Had the same thing happen on a 460 once trashed everything, rotor,pawls,washer,spring clip,and pull cord all down the drain.
FEAR NO TREE. FEAR GOD.

Offline don5477

  • 4 cube
  • **
  • Posts: 54
  • Karma: 2
Re: ms660
« Reply #6 on: December 28, 2013, 12:18:44 am »
i did check that they were coming out but didn't notice if they was going in all the way when i get the new oem parts this time, ill check that out.thanks guys

Offline Fish

  • Piped Saw
  • *****
  • Posts: 309
  • Karma: 39
Re: ms660
« Reply #7 on: December 30, 2013, 12:51:57 pm »
I have never had much luck with aftermarket starter parts for any brand.

 

Related Topics

  Subject / Started by Replies Last post
9 Replies
655 Views
Last post February 25, 2012, 08:34:02 am
by 2spud
1 Replies
113 Views
Last post September 13, 2013, 02:55:35 pm
by KilliansRedLeo
1 Replies
285 Views
Last post February 05, 2014, 08:38:42 pm
by Cut4fun .
7 Replies
168 Views
Last post September 12, 2014, 07:50:51 pm
by 660magnum
0 Replies
127 Views
Last post May 21, 2016, 09:52:45 am
by weimedog
0 Replies
199 Views
Last post November 26, 2016, 02:32:54 pm
by weimedog
3 Replies
96 Views
Last post December 12, 2017, 09:40:25 pm
by sawyer tom
Stihl 066 660 MS660

Started by Cut4fun . « 1 2 3 » Stihl

29 Replies
684 Views
Last post May 02, 2020, 02:36:33 pm
by Cut4fun .
10 Replies
201 Views
Last post January 24, 2020, 11:40:36 pm
by 3000 FPS