Author Topic: rebuilt 066 wont run  (Read 360 times)

0 Members and 0 Guests are viewing this topic.

Online jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2064
  • Karma: 158
  • Location: MD
Re: rebuilt 066 wont run
« Reply #10 on: February 18, 2014, 07:10:32 am »
The metal flywheels that I have seen are a 2 slot flywheel, do you have it in the right slot. Believe it should be in the x marked slot. I would check your flywheel key. And also check your coil gap. Have seen saw where the flywheel was not properly installed and it spin past the key and make the saw act crazy.
FEAR NO TREE. FEAR GOD.

Offline fordrocks

  • 4 cube
  • **
  • Posts: 46
  • Karma: 2
Re: rebuilt 066 wont run
« Reply #11 on: February 18, 2014, 02:18:10 pm »
This is a 1 slot metal flywheel , part # 1122 400 1209. I've tried 3 different coils with no luck. does anyone know the correct coil part # to match this flywheel ?

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: rebuilt 066 wont run
« Reply #12 on: February 18, 2014, 03:12:33 pm »
According to my records that flywheel is from a early 064 with heated handles

Should be running 1122 400 1311 coil, or 000 400 1300 or 1122 400 1303
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline fordrocks

  • 4 cube
  • **
  • Posts: 46
  • Karma: 2
Re: rebuilt 066 wont run
« Reply #13 on: February 18, 2014, 10:03:45 pm »
I don't see the 1122 400 1209 on that pdf file.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: rebuilt 066 wont run
« Reply #14 on: February 18, 2014, 10:45:03 pm »
I'm sorry I had transposed the number to 1122 400 1207

The 122 400 209 flywheel uses the 1122 400 1307  Prufrex coil
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline fordrocks

  • 4 cube
  • **
  • Posts: 46
  • Karma: 2
Re: rebuilt 066 wont run
« Reply #15 on: February 18, 2014, 11:04:28 pm »
ok, thanks!

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: rebuilt 066 wont run
« Reply #16 on: February 20, 2014, 09:05:10 am »
Any updates on this?
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline fordrocks

  • 4 cube
  • **
  • Posts: 46
  • Karma: 2
Re: rebuilt 066 wont run
« Reply #17 on: February 20, 2014, 10:36:27 pm »
I assume that if the flywheel is off an 064 then the whole bottom end is 064. So, i started from the ground up with an 066 bottom end with the plastic flywheel and built the saw again. Great spark and compression. It's getting fuel. I tried 4 different coils. Still won't run !!! >:( :-[

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: rebuilt 066 wont run
« Reply #18 on: February 21, 2014, 12:24:01 am »
The 1207 flywheel is a 064 model. This was my fault for even mentioning it.

The 066 early flywheel is a 1209.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Online jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2064
  • Karma: 158
  • Location: MD
Re: rebuilt 066 wont run
« Reply #19 on: February 21, 2014, 08:16:06 pm »
Make sure there are no bare spots in you ignition lead,may be it is grounding out once you have it hooked back up to the plug. Just a thought as you said you have great spark but maybe when it is all put together it may be grounding. Could be a bad air leak some where as well. If you are running the poly flywheel the coil you should be using is part number 1122 400 1314 or 0000 400 1305 or 0000 400 1303 the last 2 numbers are the prior numbers from the first one. Most of the coils I have seen have the part number embossed in them.
FEAR NO TREE. FEAR GOD.

 

Related Topics

  Subject / Started by Replies Last post
9 Replies
1186 Views
Last post November 05, 2014, 10:35:55 pm
by 67L36Driver
13 Replies
384 Views
Last post November 04, 2013, 05:27:49 am
by alsled
5 Replies
311 Views
Last post April 13, 2014, 11:22:26 am
by KilliansRedLeo
4 Replies
281 Views
Last post July 12, 2014, 05:55:01 pm
by KilliansRedLeo
MS360 Pro wont start

Started by ears54 « 1 2 » Stihl

10 Replies
505 Views
Last post August 16, 2015, 03:37:13 pm
by Cut4fun .
2 Replies
193 Views
Last post September 12, 2015, 09:44:05 pm
by jrdplowing
36 Replies
1532 Views
Last post February 11, 2016, 11:17:11 am
by 3000 FPS
2 Replies
381 Views
Last post December 30, 2015, 03:58:15 pm
by Cat-Face Timber
10 Replies
495 Views
Last post April 09, 2017, 03:28:22 pm
by HolmenTree
11 Replies
1902 Views
Last post June 05, 2017, 02:48:32 pm
by 3000 FPS