« previous next »
Pages: [1]   Go Down

Author Topic: Sthil 056 Ignition Module  (Read 531 times)

0 Members and 0 Guests are viewing this topic.

Offline geobee

  • pruner
  • *
  • Posts: 2
  • Karma: 0
Sthil 056 Ignition Module
« on: July 28, 2013, 08:58:24 pm »
Hi all, new to the forum, hope to be able to help others at times when able to.  Seeing that I do a bit of electrical work, a mate has lodged this oldie on me. It has no spark, but the coil has tested all good. I am leaning toward either the magneto section or the ignition block itself. Down here in Aus, they are no longer available, new or second hand. Too good of a machine to just discard because of this, and maybe someone has a bit more knowledge on this model than we do. Is there a mod than can be done, or a replacement that we dont know about. Hope someone out there can help save this quality unit from the scrap heap. Many thanks. Geoff
Logged

Share on Facebook Share on Twitter

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181
Re: Sthil 056 Ignition Module
« Reply #1 on: July 29, 2013, 08:36:32 am »
I looked it up on a service manual that I have on micro fitche .According to that this praticular model uses an internal to the flywheel solid state capacitive discharge ignition systm which is mounted on an aluminum rotor plate .

There should be a mark on this stater plate which aligns with a mark on the pocket it sits in to set it for 27 or so degrees advance .That would be when the piston is approx. 16 thou before top dead center or for the metrically inclined 2.5 to 2.7 mm.I would speculate that if the timing is out too far you would not get any spark.
Logged

Offline geobee

  • pruner
  • *
  • Posts: 2
  • Karma: 0
Re: Sthil 056 Ignition Module
« Reply #2 on: July 29, 2013, 05:09:30 pm »
Thanks for that, but the saw was running well, then just died, so I would be thinking more towards an electronic failure, rather than the plate moving. Regards. Geoff
Logged

Offline sharkey

  • Piped Saw
  • *****
  • Posts: 367
  • Karma: 37
Re: Sthil 056 Ignition Module
« Reply #3 on: July 29, 2013, 06:15:02 pm »
There is a work around off one of the chop saws.   Check the stihl ts-350/360 but I believe you will also need the flywheel.  If your saw has the Bosch ignition then your going to have to switch over to the SEM or search for a donor saw on ebay.   

The other thing Im thinking is if your 056 has a points ignition then you should be able to replace the points and condenser with a nova or atom trigger.     

Stihl should support some of these older models better than they do. 
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
19 Replies
3279 Views 		Last post January 31, 2012, 09:09:32 pm
by Al Smith
Sthil 023

Started by dolmarfan « 1 2 » Stihl

10 Replies
860 Views 		Last post January 19, 2013, 12:59:17 am
by dolmarfan
3 Replies
1197 Views 		Last post December 13, 2013, 05:00:34 pm
by brokenbudget
1 Replies
580 Views 		Last post January 07, 2014, 11:28:23 pm
by jmester
2 Replies
1620 Views 		Last post August 27, 2014, 07:50:56 am
by farmboy
8 Replies
319 Views 		Last post April 29, 2015, 11:48:00 am
by 3000 FPS
2 Replies
245 Views 		Last post July 11, 2015, 07:07:14 am
by jmester
8 Replies
4044 Views 		Last post May 14, 2016, 01:07:44 pm
by Cut4fun .
2 Replies
688 Views 		Last post January 14, 2020, 09:07:19 pm
by Girbull
7 Replies
508 Views 		Last post January 05, 2019, 05:07:42 pm
by trappermike