Author Topic: Stihl info  (Read 10656 times)

0 Members and 5 Guests are viewing this topic.

Offline jakeamondo

  • pruner
  • *
  • Posts: 1
  • Karma: 1
Re: Stihl info
« Reply #40 on: November 06, 2018, 10:47:20 am »
Useful Useful x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Stihl info
« Reply #41 on: November 06, 2018, 11:26:11 am »
OK finally came up right.  Look like spam at first. But loaded right 3rd try.

3003 650 2539  30036502539  stihl 13T replacement bar tip

Stihl misc bolt nut kit 59100071061
 
 
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Stihl info
« Reply #42 on: December 30, 2018, 09:50:44 am »
You know I have been on a kick for buying tools to make my life easier. Well one I never knew about but just bought because there was times I wish I had something better. Bought a set of stihl wrist pin punches. I know not needed, buttttttt. Just to make my life alittle easier.

OEM Stihl piston pin assembly drifts

1106 893 4700 
1107 893 4700
1108 893 4700
1110 893 4700 
1111 893 4700   
1114 893 4700 
1130 893 4700 
1135 893 4700

REDNECK Saw Repair Getter Done
Like Like x 1 View List

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2048
  • Karma: 157
  • Location: MD
Re: Stihl info
« Reply #43 on: December 30, 2018, 02:18:58 pm »
I have a few of them as well. They come in handy for sure. I really like the tool for installing the earless piston pin clips
FEAR NO TREE. FEAR GOD.
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Stihl info
« Reply #44 on: March 16, 2019, 02:41:02 pm »
conical washer 9331 630 0120
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Stihl info
« Reply #45 on: March 19, 2019, 02:25:47 pm »
Redbull =

first gen solenoid = Black - pn# 0000 120 5110 - should use with black fuel filter
current gen solenoid = White - pn# 0000 120 5104 - should use with orange fuel filter
new exploratory solenoid that apparently has now been scrapped = Green - pn# 0000 120 5111

orange fuel filter, white solenoid and new coils have 2yr warranty. After that it sounds like stihl will replace parts but you will have to pay labor.

If you have problem on the -

MS241 - he didn't have any info on the 241 yet.

MS261 cm - replace black solenoid to white solenoid and black fuel filter to orange fuel filter. (they are coming out with a kit for this (contains white solenoid and orange fuel filter) Use "RESET" (90sec choke, 60 sec idle, 5 cuts). There are no gen3 control modules/coils thus you don't use "Calibration" (30-40sec choke, 20-30sec WOT, let off after it goes from max to scream back to max :D)

MS362 cm - same as 261 above.

MS462 cm - all 462s have gen3 control modules/coils, white solenoids, and orange fuel filters. So obviously stick to doing "Calibration" and replacing white solenoid and orange fuel filter with a white solenoid and orange fuel filter.


MS661 cm - little more complicated on the 661...

If control module/coil = 4700c 4700d 4700e(gen1) 4701a(gen2) - then must stick with black solenoid, black fuel filter, and doing the "RESET" (90 sec choke, 60sec idle, 5 cuts). You should not inter change any of the parts ...apparently problems with doing so. For example a white solenoid with 4701a coil and black fuel filter.

If control module/coil = 4702 4703 4704(gen3) - then must stick with white solenoid and orange fuel filter. And of course you do a "Calibration" not a "RESET".

There is a kit specifically for the 661 which includes the ver3 coil, white solenoid, and orange fuel filter 1144 007 1801
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Stihl info
« Reply #46 on: June 22, 2019, 10:14:32 am »
Saving info someone may need someday.

REDNECK Saw Repair Getter Done

Offline joe_indi

  • 5 cube
  • ***
  • Posts: 92
  • Karma: 29
  • Location: Cochin, India
Re: Stihl info
« Reply #47 on: July 01, 2019, 09:50:23 am »
I do have the Electronic Catalogue from the 90s. And it has the Testing and Setting Data in pdf for older saws and other machines. I can screen grab the pages (painful process) or pm the file to you (easy  ;D)
Sample page below


Informative Informative x 1 Useful Useful x 1 View List

Offline joe_indi

  • 5 cube
  • ***
  • Posts: 92
  • Karma: 29
  • Location: Cochin, India
Re: Stihl info
« Reply #48 on: July 01, 2019, 09:54:25 am »
another grab
Informative Informative x 1 Useful Useful x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Stihl info
« Reply #49 on: July 01, 2019, 10:50:47 am »
@joe_indi  make sure is different then this link before you go through the trouble.  http://slugaservice-com.3dcartstores.com/assets/html/S_specs.html
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
49 Replies
12197 Views
Last post February 13, 2016, 06:19:32 pm
by farmboy
6 Replies
316 Views
Last post November 07, 2014, 08:44:37 pm
by farmboy
2 Replies
432 Views
Last post August 22, 2015, 10:26:29 am
by 1manband
0 Replies
411 Views
Last post December 29, 2015, 09:42:33 am
by Cut4fun .
0 Replies
200 Views
Last post March 17, 2016, 12:54:13 pm
by Cut4fun .
1 Replies
374 Views
Last post January 03, 2017, 02:38:07 pm
by Cut4fun .
4 Replies
306 Views
Last post August 13, 2017, 01:48:48 pm
by Cut4fun .
0 Replies
176 Views
Last post September 17, 2017, 10:30:11 am
by Cut4fun .
10 Replies
1533 Views
Last post May 02, 2019, 01:09:56 pm
by Cut4fun .
1 Replies
305 Views
Last post December 03, 2017, 08:44:10 am
by jmester