Author Topic: Stihl 084  (Read 7607 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4106
  • Karma: 166
  • OHIO REDNECK
aftermarket 084 c+p
« Reply #200 on: March 26, 2015, 01:40:15 pm »
Stihl aftermarket 084 p +c .   Done forget you can save 10% off purchase using code word in members  where to by thread here.

aftermarket 084
REDNECK Saw Repair

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22060
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: aftermarket 084 c+p
« Reply #201 on: March 30, 2015, 10:41:11 am »
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22060
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Stihl 084 carb info
« Reply #202 on: April 24, 2015, 01:16:07 pm »
Come across some old info back in 2007 where I was trying to learn the differences in HT 1 2 3 5 7 etc carbs back then.

Now still trying to find my info on which ones had the gov rev limiter type deal inside.  ???  Thinking it was 3 and ?  Not sure.


me = If you had a choice between putting back Tilly carbs for your bigger stihls.
Which is the better carb to put back and why? HT-1 or HT-7 ? or is the circuitry the same?

Which one of these carbs has better circuity for opening up for more fuel flow or are they the same?

Dennis Cahoon =  One thing about the newer HT's, they have a Hi speed jet that's in the way when you want to round slot (T-slot) the fuel area. You can do it but it's annoying to work around. When I have time, I'll take a look at the HT's I have and try to answer you question better. I would go with the HT-1.
REDNECK Saw Repair Getter Done

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: Stihl 084 carb info
« Reply #203 on: April 24, 2015, 01:53:46 pm »
Kev, the original HT has a very simple fuel circuit much like the smaller HS tillotson.  The HT11 seen on the 088, etc has a slightly different circuit as Cahoon  mentioned

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: Stihl 084 carb info
« Reply #204 on: April 24, 2015, 01:54:49 pm »
Pretty sure the pump diaphragm is the same as the smaller HS tilly

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22060
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Stihl 084 carb info
« Reply #205 on: April 24, 2015, 02:38:14 pm »
I had 3 HT-1 carbs when it was all said and done.  I know 2 of them still in Ohio.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22060
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Stihl 084 carb info
« Reply #206 on: April 24, 2015, 02:39:24 pm »
Trying to figure out which ones had that circuit that flooded them at a certain rpm like rev limited gov.  Had some that had been sealed over in saws.
REDNECK Saw Repair Getter Done

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: Stihl 084 carb info
« Reply #207 on: April 24, 2015, 03:47:26 pm »
HT 11 and 12 had the enrichment circuit I believe.  Been a while since I've worked on one.
 

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22060
  • Karma: 546
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Stihl 084 carb info
« Reply #208 on: April 24, 2015, 07:41:58 pm »
Thinking the HT 7 had that too.
REDNECK Saw Repair Getter Done

Offline Stihlboy

  • 3 cube
  • *
  • Posts: 14
  • Karma: 1
Re: Stihl 084 carb info
« Reply #209 on: May 18, 2015, 12:19:40 am »
I had 3 HT-1 carbs when it was all said and done.  I know 2 of them still in Ohio.

Nope... all 3 still here :) remember the carb in my pp084? What all was done to that thing...

 

Related Topics

  Subject / Started by Replies Last post
Woods ported 066

Started by Cut4fun . « 1 2 » Stihl

13 Replies
1064 Views
Last post December 20, 2015, 10:12:31 pm
by Cut4fun .
37 Replies
1485 Views
Last post August 20, 2014, 11:35:33 am
by JohnG28
2 Replies
556 Views
Last post September 03, 2011, 11:53:35 am
by Cut4fun
9 Replies
667 Views
Last post February 25, 2012, 08:34:02 am
by 2spud
11 Replies
533 Views
Last post December 06, 2012, 07:08:32 am
by Al Smith
7 Replies
266 Views
Last post September 02, 2013, 05:12:17 pm
by Old Iron Logging
4 Replies
232 Views
Last post August 09, 2014, 04:39:02 pm
by SawTroll
3 Replies
155 Views
Last post January 14, 2015, 03:25:56 am
by 660magnum
29 Replies
626 Views
Last post September 28, 2015, 12:21:17 pm
by aclarke
0 Replies
129 Views
Last post March 21, 2019, 10:42:16 am
by Cut4fun .