Author Topic: Stihl 084  (Read 8095 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22571
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Making stihl 084 muffler
« Reply #240 on: October 26, 2017, 10:30:32 pm »
Phil = If there's enough interest in the cast 084 mufflers I'll start by casting a batch of ten (10), price would be $200- usd each.

Thanks, Phil.

Paper specs and what I said in 2008. = weight of PHO of a MS880 is 22.3LBS flush handle, 084 same PHO 20.7LBS, 088 same PHO 21.8LBS.
I was comparing the MS880 and 084, yes I have lifted and ran both. and could feel the weight difference from the get go. I know after running either for any amount of time the extra weight of the 880 wouldn't matter anyways, but there is a notable bulk of the 880 sitting beside the 084, the 084 seems more streamed lined. I wouldn't kick any of them out of the garage though.

084 20.7LBS 8.6bhp

088 21.8LBS 8.7bhp

MS880 22.3lbs 8.6bhp
REDNECK Saw Repair Getter Done
Like Like x 1 View List

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171
Re: Making stihl 084 muffler
« Reply #241 on: October 26, 2017, 10:46:11 pm »
Good price. I bet he's sell them.
Like Like x 1 View List

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4334
  • Karma: 189
  • OHIO REDNECK
Re: Stihl 084
« Reply #242 on: July 19, 2018, 12:02:08 pm »
Merged most of the stihl 084 info into one thread to make it easier to find.

Also saving some old pics of 084's I used to run.

REDNECK Saw Repair

 

Related Topics

  Subject / Started by Replies Last post
Woods ported 066

Started by Cut4fun . « 1 2 » Stihl

13 Replies
1164 Views
Last post December 20, 2015, 10:12:31 pm
by Cut4fun .
37 Replies
1686 Views
Last post August 20, 2014, 11:35:33 am
by JohnG28
2 Replies
561 Views
Last post September 03, 2011, 11:53:35 am
by Cut4fun
9 Replies
759 Views
Last post February 25, 2012, 08:34:02 am
by 2spud
1 Replies
38 Views
Last post February 20, 2012, 07:13:14 pm
by Cut4fun
11 Replies
601 Views
Last post December 06, 2012, 07:08:32 am
by Al Smith
7 Replies
275 Views
Last post September 02, 2013, 05:12:17 pm
by Old Iron Logging
4 Replies
234 Views
Last post August 09, 2014, 04:39:02 pm
by SawTroll
29 Replies
651 Views
Last post September 28, 2015, 12:21:17 pm
by aclarke
0 Replies
177 Views
Last post March 21, 2019, 10:42:16 am
by Cut4fun .