« previous next »
Pages: [1] 2   Go Down

Author Topic: tools  (Read 1453 times)

0 Members and 0 Guests are viewing this topic.

Offline stihlbro

  • 4 cube
  • **
  • Posts: 70
  • Karma: 9
  • Location: virginia
tools
« on: March 11, 2011, 01:29:42 pm »
If there was one tool that I ever bought that holds bragging rights it is this. Its a snap-on cordless driver with 1/4 inch quick change bits. And a Irwin Tool set.
Logged

Share on Facebook Share on Twitter

Offline stihlbro

  • 4 cube
  • **
  • Posts: 70
  • Karma: 9
  • Location: virginia
Re: tools
« Reply #1 on: March 11, 2011, 01:36:39 pm »
Now I'm not against t-handle drivers, but this thing will pull cylinder hold down bolts, mufflers, top covers, carburetors and what ever else you need. The quick change bits are nice. The T-27 is showing some wear but it's been used alot!!!!!!!!!!!!
Logged

Offline stihlbro

  • 4 cube
  • **
  • Posts: 70
  • Karma: 9
  • Location: virginia
Re: tools
« Reply #2 on: March 11, 2011, 01:38:39 pm »
How did that picture show upside down?????????? You can go to home depot and get a Makita cordless driver for less. I dont know about the bits. If you dont have it, it is a good investment. Trust me!!!!!!!!
Logged

Offline stihlbro

  • 4 cube
  • **
  • Posts: 70
  • Karma: 9
  • Location: virginia
Re: tools
« Reply #3 on: March 11, 2011, 01:43:14 pm »
Another tool used is a used bar with a clamp that you can purchase from a local hardware store. I use it to touch up chains off a saw and if lucky try alittle square filing on. ??? The clamp idea come from a gentleman out west. The clamp cost a few bucks. You can adjust it accordingly.
Logged

Offline stihlbro

  • 4 cube
  • **
  • Posts: 70
  • Karma: 9
  • Location: virginia
Re: tools
« Reply #4 on: March 11, 2011, 01:50:20 pm »
Logged

Offline stihlbro

  • 4 cube
  • **
  • Posts: 70
  • Karma: 9
  • Location: virginia
Re: tools
« Reply #5 on: March 11, 2011, 01:55:49 pm »
Pictures are crappy, I took them on my cellphone and uploaded to photobucket. The smart phones are smarter than me. ;D
Logged

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4574
  • Karma: 215
  • OHIO REDNECK
Re: tools
« Reply #6 on: March 11, 2011, 02:50:24 pm »
Clamp? What's it do hold chain to bar without moving?  Where purchased?
Logged

Offline stihlbro

  • 4 cube
  • **
  • Posts: 70
  • Karma: 9
  • Location: virginia
Re: tools
« Reply #7 on: March 11, 2011, 03:07:46 pm »
That's right, hold the tooth! It does a pretty good job! We have one welded on each end of the bar so if you have to flip the chain for the other side. Or you can clamp the chain on both ends, like for checking rakers.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23416
  • Karma: 661
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: tools
« Reply #8 on: March 11, 2011, 03:18:28 pm »
I've never seen a clamp like that.

How would I go about looking or asking for it in the hardware stores?
Logged

Offline stihlbro

  • 4 cube
  • **
  • Posts: 70
  • Karma: 9
  • Location: virginia
Re: tools
« Reply #9 on: March 11, 2011, 04:12:07 pm »
A local Harbor freight has some here. The cost is like $1.29, I would send some your way if you wanna try some. In the picture they are welded to a xl12 homelite bar.
Logged
Pages: [1] 2   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
37 Replies
5773 Views 		Last post February 21, 2014, 03:18:14 am
by fordfairlane78
1 Replies
330 Views 		Last post June 29, 2013, 12:46:13 pm
by RoyM
1 Replies
366 Views 		Last post November 15, 2013, 02:23:18 am
by KilliansRedLeo
33 Replies
2192 Views 		Last post October 22, 2014, 11:13:35 pm
by srcarr52
2 Replies
373 Views 		Last post December 18, 2013, 09:29:41 pm
by fossil
20 Replies
1779 Views 		Last post December 30, 2013, 04:18:38 am
by Magnus
38 Replies
2147 Views 		Last post December 07, 2018, 02:46:41 pm
by Philbert
2 Replies
463 Views 		Last post November 05, 2016, 01:21:29 pm
by fisaw
4 Replies
816 Views 		Last post November 04, 2017, 11:29:52 pm
by mdavlee .
0 Replies
224 Views 		Last post June 11, 2018, 11:27:52 am
by Cut4fun .