Author Topic: Poulan Poulan Pro bars - OEM & Oregon  (Read 1228 times)

0 Members and 0 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan Poulan Pro bars - OEM & Oregon
« Reply #20 on: November 02, 2015, 04:10:30 am »
I think I know what saw that bar is going on... 8)
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan Poulan Pro bars - OEM & Oregon
« Reply #21 on: November 02, 2015, 07:42:59 am »
I think I know what saw that bar is going on... 8)

That PP380 you went through for him. I bet.  ;)
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan Poulan Pro bars - OEM & Oregon
« Reply #22 on: November 02, 2015, 03:28:15 pm »
I think I know what saw that bar is going on... 8)

That PP380 you went through for him. I bet.  ;)

That's what I'm thinking.  The 20" laminate bar that came to me with it when the saw was shipped was completely trashed.  Didn't even bother sending it on with the saw....
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan Poulan Pro bars - OEM & Oregon
« Reply #23 on: November 02, 2015, 04:36:50 pm »
I couldnt believe I had a poulan sprocket nose replaceable 20" K041 mount here. I told him I didnt have one and low and behold I came across one. Not a clue where it came from.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
Poulan 475

Started by Cut4fun « 1 2 ... 35 36 » Poulan

351 Replies
9029 Views
Last post October 25, 2018, 02:04:51 pm
by Cut4fun .
222 Replies
6780 Views
Last post June 29, 2020, 07:46:24 pm
by Cut4fun .
4 Replies
549 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
Poulan Bars OEM

Started by Cut4fun . « 1 2 » Poulan

19 Replies
481 Views
Last post February 11, 2018, 01:13:52 pm
by Cut4fun .
0 Replies
353 Views
Last post October 12, 2015, 10:41:19 am
by chainsawlady
4 Replies
152 Views
Last post November 15, 2015, 10:19:28 am
by SDB777
2 Replies
230 Views
Last post May 21, 2017, 08:59:45 pm
by Cut4fun .
8 Replies
219 Views
Last post December 31, 2018, 09:04:53 am
by Cut4fun .
1 Replies
73 Views
Last post April 03, 2020, 12:03:39 am
by ssidwell
2 Replies
49 Views
Last post June 12, 2020, 10:13:07 am
by Cut4fun .