« previous next »
Pages: 1 2 3 4 [5] 6 7 8 9 10 ... 17   Go Down

Author Topic: Welding Chainsaw Parts  (Read 9685 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23514
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Welding Chainsaw Parts
« Reply #40 on: November 18, 2013, 08:25:05 pm »
Quote from: 3000 FPS on November 18, 2013, 08:18:34 pm
I wanted to show a before and after of a weld job on a Poulan 3750 Tim Allen.   The area where the chain adjuster sits was broken out because the clutch cover got tightened down on it.   A lot of the welding was done from the back side.



I had a 330 I bought for parts  like that. I think they put bar on, missed the bar adjuster and pushed it through case when cover was tighten down.  I rednecked it and put the saw back into firewood service.   So far good to go.

Now you know the welding I want to see, is that other TA that had bow saw on it.  Before / After pics pleaseeeeeee   ;D
Logged

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4695
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Welding Chainsaw Parts
« Reply #41 on: November 18, 2013, 08:31:39 pm »
It is coming I have the saw all tore down and the case split.   All I have to do now is get out to my garage and weld it.


Logged
PP 505, 475, 445.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4695
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Welding Chainsaw Parts
« Reply #42 on: November 18, 2013, 08:35:21 pm »
Here is another weld job that I did on a Poulan 3400 clutch cover.   The part that holds the chain adjust in place was broken out.



This is after the welding was done.   The dark areas are JB Weld that I used to fill in some small shallow pitting.


This is how I managed to keep the hole in place for the chain adjuster while I welded it.
Logged
PP 505, 475, 445.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Welding Chainsaw Parts
« Reply #43 on: November 18, 2013, 08:40:33 pm »
Good job
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4695
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Welding Chainsaw Parts
« Reply #44 on: November 18, 2013, 08:53:49 pm »
I do not remember if I ever showed this weld job that I did on a Husqvarna crankshaft that was broken on the end where the c-clip goes. 





When the welding was completed I duct taped the piston to the counter balance of the crankshaft and then turned it on my lathe to get the groove for the c-clip back to the correct width. 
Logged
PP 505, 475, 445.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Welding Chainsaw Parts
« Reply #45 on: November 18, 2013, 09:03:42 pm »
I have a 372 crank that is broken like that.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4695
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Welding Chainsaw Parts
« Reply #46 on: November 18, 2013, 09:07:47 pm »
Quote from: 660magnum on November 18, 2013, 09:03:42 pm
I have a 372 crank that is broken like that.

Well now you know it can be fixed.
Logged
PP 505, 475, 445.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4695
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Welding Chainsaw Parts
« Reply #47 on: November 19, 2013, 11:32:12 am »
This is the clutch cover on a 306A that is **** where the bucking spike attaches.   This is pretty common and  I have seen it quit a bit.  On the back side you can not see I pressed a nut into the cover so a screw can now be put in to hold the spike in place.



Logged
PP 505, 475, 445.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Welding Chainsaw Parts
« Reply #48 on: November 19, 2013, 11:58:38 am »
Good clean repair
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4695
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Welding Chainsaw Parts
« Reply #49 on: November 19, 2013, 07:33:13 pm »
Well I finished up the welding on the 3750 that was pictured above.   There was a gap between the crankcase and clutch cover where someone ground it out to fit a bow bar.   
   
I have been collecting parts for this saw for quit awhile now so I should be good to go and can start cleaning everything up for re-assembly.



Logged
PP 505, 475, 445.
Pages: 1 2 3 4 [5] 6 7 8 9 10 ... 17   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
0 Replies
671 Views 		Last post April 19, 2012, 10:08:34 am
by tommysp61
3 Replies
934 Views 		Last post June 07, 2012, 02:47:11 pm
by Dh1984
2 Replies
616 Views 		Last post February 08, 2013, 10:51:18 pm
by mattinky
0 Replies
245 Views 		Last post December 02, 2013, 10:34:35 am
by Forester Parts
5 Replies
1646 Views 		Last post February 08, 2018, 08:28:16 pm
by Al Smith
3 Replies
503 Views 		Last post November 05, 2015, 12:02:37 pm
by Cut4fun .
8 Replies
787 Views 		Last post April 29, 2016, 11:47:09 am
by chy_farm
0 Replies
506 Views 		Last post December 05, 2015, 10:17:42 am
by Cut4fun .
1 Replies
567 Views 		Last post April 06, 2016, 04:17:50 pm
by aclarke
3 Replies
2556 Views 		Last post May 06, 2020, 09:13:40 am
by Al Smith