Author Topic: Chain damage  (Read 533 times)

0 Members and 27 Guests are viewing this topic.

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna

  • Total Badges: 29
    Badges: (View All)
    2000 post CR Staff One year Anniversary 1000 Posts Never Sleep Group
Re: Chain damage
« Reply #10 on: January 13, 2014, 06:52:32 am »
Keeping your chain properly sharpened, tensioned and oiled not only makes the job of cutting easier but keeps you safe! I have seen lots of nasty cuts and damage to saws from chains jumping the bar.
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline Philbert

  • Gas Hotsaw
  • ******
  • Posts: 563
  • Karma: 76

  • Total Badges: 23
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Level 5 Fifth year Anniversary 500 Posts Fourth year Anniversary
Re: Chain damage
« Reply #11 on: January 19, 2014, 09:48:17 pm »
Other ways to remove the burrs from the drive links, are to hold the chain loop 'inside out' (so that the points of the drive links are facing out) and remove the burrs with a bench grinder.  I prefer a ScotchBrite wheel for this, which leaves a polished finish, but any fine grinding wheel will do.  Don't take off any more than necessary, because you still want it to fit the sprockets.

If you want, you can clean up the front 'tang' of the drive link by running a round file through it.

Don't toss the chain.  It is something that happens quite frequently, often when twigs or small branches get caught between the chain and the bar, and is easily and effectively repaired.

Philbert

Offline bustedknuckles

  • 4 cube
  • **
  • Posts: 70
  • Karma: 11

  • Total Badges: 13
    Badges: (View All)
    Second year Anniversary Karma Good Level 3 One year Anniversary 50 Posts 10 Posts
Re: Chain damage
« Reply #12 on: January 26, 2014, 06:07:49 pm »
The burrs can also be pounded flat but I usually grind them off. I use the method someone else mentioned of turning the chain inside out and hitting the high spots on a bench grinder. It can be done in just a few minutes depending on how many links are damaged. It usually is only 5 links or so.

Almost every time I have derailed a chain, I was cutting brush, saplings and other small diameter stuff. One thing I like to avoid if possible is splintered wood like where a large branch gets broken in a storm. Those splinters seem to cause thrown chains when being bucked.

 

Related Topics

  Subject / Started by Replies Last post
5 Replies
914 Views
Last post January 31, 2012, 10:10:59 pm
by Al Smith
3 Replies
875 Views
Last post December 11, 2018, 04:09:16 pm
by fisaw
12 Replies
1298 Views
Last post October 05, 2013, 09:25:13 am
by leec
26 Replies
2056 Views
Last post February 03, 2014, 08:30:34 am
by SawTroll
15 Replies
999 Views
Last post December 12, 2013, 02:14:46 pm
by Gregsl
2 Replies
611 Views
Last post December 19, 2013, 11:47:37 pm
by RoyM
1 Replies
386 Views
Last post December 24, 2013, 11:36:57 pm
by Cut4fun .
0 Replies
282 Views
Last post January 12, 2014, 05:35:35 pm
by Cut4fun
Palm damage

Started by Cut4fun . « 1 2 » Welding Shop

15 Replies
1124 Views
Last post November 23, 2015, 04:45:02 pm
by Eccentric
7 Replies
653 Views
Last post August 25, 2017, 06:40:44 am
by jmester