Author Topic: CS-400 piston  (Read 249 times)

0 Members and 0 Guests are viewing this topic.

Offline brettl

  • 6 cube
  • ****
  • Posts: 179
  • Karma: 7
CS-400 piston
« on: January 07, 2017, 12:50:19 am »
Does the CS-400 share piston design with any other saws? I've been trying to find an aftermarket piston with no luck. Thanks
Sthil Man. 011AV, 015, 020, 020, 024, 025, 026, 028 WB(2), 028AV, 028 Super, 029 Super(2), 039, 041, 192TC, 200T, 250, 260, 390, 440, 441

Social Buttons


Offline pleasant

  • 3 cube
  • *
  • Posts: 9
  • Karma: 1
  • Location: UK
Re: CS-400 piston
« Reply #1 on: January 07, 2017, 04:47:32 pm »
No, sorry. Echo only.....and it's a piston and barrel kit, not just a piston I'm afraid.

Offline brettl

  • 6 cube
  • ****
  • Posts: 179
  • Karma: 7
Re: CS-400 piston
« Reply #2 on: January 07, 2017, 10:33:02 pm »
I was afraid of that. Its a little surprising, considering the popularity of the saw and all the problems folks have getting them lean from the dealer. So far, I've only found the piston kit (wrist pin, clips, etc) on eBay for $55. Hate to put that much in just a piston. I'm going to tear it down and make sure of the cylinder and bottom end before I buy a piston.
Sthil Man. 011AV, 015, 020, 020, 024, 025, 026, 028 WB(2), 028AV, 028 Super, 029 Super(2), 039, 041, 192TC, 200T, 250, 260, 390, 440, 441

Online farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1038
  • Karma: 109
  • Location: Hayesville, NC
Re: CS-400 piston
« Reply #3 on: January 07, 2017, 10:38:27 pm »
Check w/Performance Outdoor Equipment Nate is an Echo dealer good guy great to do business with.
Shep

Offline mountainlake

  • 5 cube
  • ***
  • Posts: 111
  • Karma: 17
Re: CS-400 piston
« Reply #4 on: January 17, 2017, 05:30:01 am »
 
 A piston kit with ring and wrist pin on SEPW is $40.15. I wouldn't even think of using aftermarket as the OEM is really light and made well.  Steve

Offline leec

  • 6 cube
  • ****
  • Posts: 240
  • Karma: 11
  • Location: Huntsville, Ontario
Re: CS-400 piston
« Reply #5 on: September 09, 2017, 12:19:16 pm »
 Steve, Where can I find SEPW?  I'm going to need a piston for a CS-440 shortly. 
Thanks Lee

Offline mountainlake

  • 5 cube
  • ***
  • Posts: 111
  • Karma: 17
Re: CS-400 piston
« Reply #6 on: September 14, 2017, 05:12:38 pm »
Steve, Where can I find SEPW?  I'm going to need a piston for a CS-440 shortly. 
Thanks Lee



  http://www.sepw.com/   Its best to order a few things at the same time as shipping doesn't vary much from a small order to a large order.  Steve

 

Related Topics

  Subject / Started by Replies Last post
11 Replies
624 Views
Last post March 07, 2011, 02:39:37 pm
by Old Iron Logging
6 Replies
177 Views
Last post October 16, 2013, 04:50:13 pm
by Al Smith
8 Replies
236 Views
Last post January 23, 2015, 05:25:39 pm
by Cut4fun .
9 Replies
163 Views
Last post March 04, 2015, 03:15:47 pm
by GCC
Top of piston has....

Started by SDB777 « 1 2 3 » Stihl

21 Replies
322 Views
Last post September 25, 2015, 02:29:31 pm
by Cut4fun .
4 Replies
173 Views
Last post December 15, 2015, 10:18:08 am
by dannyupsolate
12 Replies
185 Views
Last post May 23, 2017, 01:51:26 pm
by Cut4fun .
Harvest piston

Started by dpjones « 1 2 » Stihl

10 Replies
157 Views
Last post June 21, 2017, 06:14:43 pm
by sharkey
7 Replies
82 Views
Last post September 17, 2017, 08:36:07 am
by Fishnuts2
Black Piston

Started by dpjones « 1 2 » Stihl

10 Replies
50 Views
Last post September 20, 2017, 01:22:31 pm
by mdavlee .