« previous next »
Pages: [1] 2   Go Down

Author Topic: 262xp won't stay running  (Read 3216 times)

0 Members and 40 Guests are viewing this topic.

Offline

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0

    • Total Badges: 8
    Badges: (View All)
    Level 2 Windows User Combination Topic Starter Level 1 First Post
262xp won't stay running
« on: September 15, 2015, 02:05:53 pm »
I have a 262xp that I love. Had problems last year so I took it to a husky technician. It would run for about a minute the die. Acts like it's not getting fuel. The technician put on a new cylinder and said it was fixed. Same problem. I don't think I needed the cylinder but oh well. Back to square one. Can't get it running. Ant thoughts?  Thanks. Tim
Logged

Share on Bluesky Share on Facebook

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

    • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: 262xp won't stay running
« Reply #1 on: September 15, 2015, 03:34:52 pm »
Check the fuel tank breather. Long pencil shaped plastic piece pressed into the upper portion of the fuel tank. Probably have to loosen the tank screws from the motor to access. 
Logged

Offline

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4709
  • Karma: 320
  • Location: Carpenter, Wyoming

    • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: 262xp won't stay running
« Reply #2 on: September 15, 2015, 06:12:39 pm »
Or you can crack the fuel cap open alittle to let air into the tank to see if it stays running or dies.   If it stays running then you know the vent is plugged up.

Could be a bad fuel filter.   Checked fuel line and make sure it is not showing any cracking any where.   

When it dies pull the plug attach it to the plug wire and hold it against the top of the cylinder and verify you have spark.

There are other possibilities but this is a good place to start.
Logged
PP 505, 475, 445.

Offline

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0

    • Total Badges: 8
    Badges: (View All)
    Level 2 Windows User Combination Topic Starter Level 1 First Post
Re: 262xp won't stay running
« Reply #3 on: September 15, 2015, 09:11:45 pm »
Thanks for the insight. I'll try the suggestions as soon as I can. Tim
Logged

Offline

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0

    • Total Badges: 8
    Badges: (View All)
    Level 2 Windows User Combination Topic Starter Level 1 First Post
Re: 262xp won't stay running
« Reply #4 on: September 17, 2015, 01:10:58 pm »
Took fuel tank off but couldn't find a vent tube. Put back togeather and loosened cap and it seemed to do fine. Only thing coming out of tank was fuel line to carb.
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: 262xp won't stay running
« Reply #5 on: September 17, 2015, 01:25:39 pm »
The vent is supposed to be on the right side (highest point) of the tank.

When assembled in the tank - It is just a round place of porous material. About 5/16" in diameter.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

    • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: 262xp won't stay running
« Reply #6 on: September 17, 2015, 04:40:13 pm »
Probabaly have to loosen the tank from the motor to access the vent. They can be a little difficult to remove...
Logged

Offline

  • 3 cube
  • *
  • Posts: 6
  • Karma: 0

    • Total Badges: 8
    Badges: (View All)
    Level 2 Windows User Combination Topic Starter Level 1 First Post
Re: 262xp won't stay running
« Reply #7 on: September 17, 2015, 09:31:07 pm »
I took the tank off. Couldn't find anything but the fuel line coming out of the top and going to the carb. The saw is an early model. The date stamp on the tank is 95.
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: 262xp won't stay running
« Reply #8 on: September 17, 2015, 10:38:14 pm »
The vent on the ones I have seen is actually shaped somewhat like a ball point pen. But all of the vent but the very end is inside to fuel tank.

You are looking for the very butt end of the vent on the outside of the tank.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • 4 cube
  • **
  • Posts: 47
  • Karma: 8

    • Total Badges: 16
    Badges: (View All)
    Level 4 Fifth year Anniversary Fourth year Anniversary Third year Anniversary Second year Anniversary Level 3
Re: 262xp won't stay running
« Reply #9 on: October 30, 2015, 06:39:35 pm »
Pics?
Logged
Pages: [1] 2   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
4 Replies
4085 Views 		Last post February 21, 2012, 09:43:13 am
by mweba
17 Replies
5230 Views 		Last post November 25, 2013, 01:09:47 pm
by crankincraig
4 Replies
1342 Views 		Last post June 20, 2014, 09:24:30 am
by Fish
12 Replies
3220 Views 		Last post July 25, 2014, 05:55:19 pm
by SawTroll
3 Replies
4763 Views 		Last post October 28, 2014, 11:40:10 pm
by aclarke
6 Replies
5027 Views 		Last post July 05, 2016, 09:33:48 am
by Cut4fun .
3 Replies
1662 Views 		Last post February 03, 2018, 09:41:05 pm
by bud
2 Replies
2656 Views 		Last post July 04, 2018, 08:14:36 am
by Cut4fun .
2 Replies
1123 Views 		Last post August 31, 2018, 10:10:01 am
by Cut4fun .
5 Replies
2318 Views 		Last post March 24, 2020, 01:44:07 pm
by Cut4fun .