Author Topic: 3120 unlimited coil source  (Read 2977 times)

0 Members and 3 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23706
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: 3120 unlimited coil source
« Reply #20 on: May 12, 2016, 08:35:53 pm »
 Italy made.

Has DAYED 4 on coil and designed in Italy on coil.

ITALY standard on box.  Professional parts. Green box. Original quality 100%







Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23706
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: 3120 unlimited coil source
« Reply #21 on: May 12, 2016, 08:36:58 pm »
I had to make alittle clearance with different location where lead ran out.


Offline snowsalot

  • 3 cube
  • *
  • Posts: 16
  • Karma: 2

  • Total Badges: 8
    Badges: (View All)
    10 Posts Level 2 Karma Topic Starter Level 1 First Post
Re: 3120 unlimited coil source
« Reply #22 on: May 16, 2016, 07:02:07 pm »
Fit perfectly except had to bend a small tab at the back of coil flat.
Didn't have to do any grinding. Saw is reving to 13000 no load. Unscrewed the short coil wire and installed the wire from the limited coil. Next step is a mild muffler mod (any suggestions) and enlarging the high speed jet in carburetor to richen it up a bit. I have  seen 1.16mm as a possible size ?

Sent from my SM-G900W8 using Tapatalk

Like Like x 1 View List

Offline snowsalot

  • 3 cube
  • *
  • Posts: 16
  • Karma: 2

  • Total Badges: 8
    Badges: (View All)
    10 Posts Level 2 Karma Topic Starter Level 1 First Post
Re: 3120 unlimited coil source
« Reply #23 on: May 16, 2016, 07:14:10 pm »


Sent from my SM-G900W8 using Tapatalk

Like Like x 1 View List

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

  • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: 3120 unlimited coil source
« Reply #24 on: May 16, 2016, 07:17:27 pm »
I would be conservative with enlarging the high speed jet a little bit and then see how it runs so you can ease up onto the perfect size?

If you are the ham fisted type and go too large, you can always solder it up and start over?

We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .
Like Like x 1 View List

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171

  • Total Badges: 31
    Badges: (View All)
    Level 6 Sixth year Anniversary Fifth year Anniversary 1000 Posts Fourth year Anniversary 500 Posts
Re: 3120 unlimited coil source
« Reply #25 on: May 16, 2016, 07:23:03 pm »
You can close it off and go back if you go too far. I can't remember what step up is. 1.16mm is pretty big. I guess I could go look at mine and see what size it is.
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23706
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: 3120 unlimited coil source
« Reply #26 on: May 16, 2016, 09:03:07 pm »
Had to bend that tab on this one too.

 

Related Topics

  Subject / Started by Replies Last post
4 Replies
1937 Views
Last post February 28, 2015, 11:59:49 am
by Cut4fun
0 Replies
338 Views
Last post August 11, 2011, 04:07:35 pm
by Roanoker494
43 Replies
2968 Views
Last post January 26, 2016, 01:16:30 pm
by Cut4fun .
8 Replies
525 Views
Last post January 22, 2014, 11:23:10 pm
by jockeydeuce
17 Replies
2508 Views
Last post February 14, 2014, 10:46:23 am
by 660magnum
12 Replies
3743 Views
Last post March 27, 2016, 01:48:26 pm
by gregh
8 Replies
479 Views
Last post April 27, 2014, 01:11:55 pm
by KilliansRedLeo
23 Replies
1943 Views
Last post November 04, 2014, 03:13:07 pm
by bloodontheice
7 Replies
416 Views
Last post December 15, 2014, 01:28:20 pm
by 660magnum
16 Replies
1840 Views
Last post May 06, 2017, 10:33:19 am
by Cut4fun .