Author Topic: 576xp updated piston and Cylinder on ebay????? Help  (Read 1586 times)

0 Members and 18 Guests are viewing this topic.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

  • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
+1
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline Jason K

  • 6 cube
  • ****
  • Posts: 190
  • Karma: 7
  • Location: Iowa

  • Total Badges: 16
    Badges: (View All)
    Level 4 Third year Anniversary Second year Anniversary Karma Good One year Anniversary Level 3
I forgot to ask two things. 1. What size of allen wrench and length of do I need to remove and install the cylinder on it.  2. What rpm should I set it at for break in..


Thanks
Jason

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC

  • Total Badges: 31
    Badges: (View All)
    Level 6 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary 1000 Posts Old Browser
32:1 synthetic mix oil, premium nonE fuel.  I run mine like I stole it.  Same way we used to do our motors when we used to dirt track.  Everybody has their own method some do heat cycles, some do light load,  etc.  Here is how I've done it for over 50 yrs.
http://www.mototuneusa.com/break_in_secrets.htm
Shep

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna

  • Total Badges: 29
    Badges: (View All)
    2000 post CR Staff One year Anniversary 1000 Posts Never Sleep Group
The cylinder bolts are 4mm M5 hex cap screws, torque spec is 14NM. Harbor Freight sells a set of 3/8 metric long reach allens on the cheap.

http://www.harborfreight.com/38-in-drive-metric-long-reach-hex-bit-socket-set-7-piece-67890.html
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline Jason K

  • 6 cube
  • ****
  • Posts: 190
  • Karma: 7
  • Location: Iowa

  • Total Badges: 16
    Badges: (View All)
    Level 4 Third year Anniversary Second year Anniversary Karma Good One year Anniversary Level 3
Thanks for the Info guy's

Jason

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna

  • Total Badges: 29
    Badges: (View All)
    2000 post CR Staff One year Anniversary 1000 Posts Never Sleep Group
I made a Mistake the cylinder bolts are NOT 4mm/m5 they are 5mm/M6x25mm. Not to worry though, the HF set has the correct size. The only Husqvarna saws that will throw you a curve are the 272s/288s and a couple others that use 3/16.
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

 

Related Topics

  Subject / Started by Replies Last post
0 Replies
473 Views
Last post May 24, 2012, 08:20:22 pm
by MP5N
63 Replies
3692 Views
Last post October 26, 2013, 05:32:17 pm
by davbell22602
38 Replies
2293 Views
Last post June 05, 2013, 09:15:45 pm
by Al Smith
8 Replies
1054 Views
Last post July 30, 2013, 09:20:17 am
by farmboy
19 Replies
1408 Views
Last post September 09, 2013, 09:51:10 pm
by doreadeal
54 Replies
2535 Views
Last post February 09, 2014, 05:37:39 pm
by wbhburn
1 Replies
560 Views
Last post March 09, 2014, 03:41:36 pm
by stihls066
1 Replies
383 Views
Last post March 11, 2014, 04:13:31 pm
by Cut4fun .
17 Replies
1493 Views
Last post May 12, 2014, 12:40:25 am
by sharkey
4 Replies
447 Views
Last post March 10, 2015, 10:43:39 am
by 660magnum