Chainsaw Repair
Husqvarna - Stihl - Poulan - Jonsered - Dolmar chainsaws and more => Chainsaws not listed - Gas OPE => Topic started by: Cut4fun . on October 29, 2023, 10:47:42 pm
-
Made this from a guys clone 3120 this morning.
For my groups morning laugh.
Thats the neat thing about clones. Can mess around with them too.
They even have clone only race classes at Sawfest.
-
https://youtu.be/bzU20TX0Ue8
-
Guy in my CR group from Romania playing with the farmertec G3120 in poplar
https://youtu.be/-PiRPMN_P7s
-
Joe's pipe he made for that stock run above. Check out the gains just a pipe did on stock saw. :o
He sells these pipes in several kit versions. Flat roll your own cones or rolled and just a weld cones.
-
Stock OEM and clone 3120's done by Joe on his dyno.
OEM husqvarna 3120 dyno and his clone 3120
-
Here is a stock clone 3120 on Joe's dyno with a muffler then on his pipe.
Notice where the power in cut would be.
-
Thanks to Ethan for leading the horse to water.
The aftermarket WG to buy.
Not those other ones that use HT inside.
Then if needing H just have one of the trusted guys do it in these WG ones or oem one.
Not worth buying the aftermarket H side WG fakes with HT one by neojunk.
-
Several folks having same issue with neojunk = neotec carb 3120 8120.
Few of us swore that clone company off. Their just to far behind compared to Farmertec today.
neojunk 3120 8120 carb kit in their H carbs are horrible. I swear the pump dia in this is double the thickness and and stiff like a kit been run on emix
Just smh again this morning checking out the kit the new carb came with.
-
No wonder folks have issues with neojunk clone carbs. Brand new carb and the diaphragm is stiff from get go.
Never had mix across it or installed yet.
It’s not even close to being pliable for pumping like Tillotson kit.
Inside round metal piece was bent alittle too.
-
Checking out the neojunk clone H side carb for 3120. Never put it on saw and pump diaphragm feels like one I would replace when stiff.
Reason why a bunch of us swore off on this clone maker. They are way behind. Farmertec non H carb works great. These neojunk ones are hit and miss.
-
Guy from Romania in my group. He went unlimited coil and ported it says.
https://youtu.be/tzWzh_rItNE
-
Never mind on question got answer in my CRG already. 8)
= 3/16 (.187) female spade connector. I have to order the non insulated ones but I think the auto parts stores have the insulated ones. They're used on a lot of speakers.
-
What is the right female end for the coil connection?
Changing mine back forth and got in hurry pulled dang thing apart.
My redneck quick fix with bigger end I had on hand.
-
Just playing to see how she acts unlimited in same wood I tested in with limited coil. 3/8 8T
Pushing hard in cuts testing. Was able to pull down couple times.
https://youtu.be/d-4mOR4-5wI
-
Since last thread on Farmertec G3120 coils and Caleb worked with the oem 395 coil. His was drop In.
I ordered a G395 afm coil to try out. From Jes and Scott at www.Bluesaws.com .
It wasn’t drop in like oem.. I had to grind lower to clear fly.
Started and stopped checking when I seen 12.8K on tach. Just so you know the afm G395 coil works for unlimited too.
My afm 272 coil didn’t work. Stopped at 10.7k.
My oem 272 coil was no spark.
I do have a 3120 H side carb now after testing more with non H stock carb.
I put everything back on and as used was 11.9k with stock carb.
Testing and checking plug.
-
If you know you know. ;)
If and when needed.
When I go unlimited too.
Air filter
503 14 16-01 basket 503141601
503 14 18-02 FOAM 503141802
503 89 53-01 FELT 503895301
-
Guy from overseas got one too. He playing with his little deeper.
https://youtu.be/tzWzh_rItNE
-
husqvarna 3120 unlimited coil
I told Caleb to stick the 395 coil in the Farmertec G3120 just because it looks so close to me. Being he didnt have a OEM 272 coil on hand. His AFM 272 coil wouldnt let it get into upper rpm's either, only 10.4k.
He told me it is now 13.2K without the H side carb just using non adjustable carb.
He didnt say if needed to grind on 395 like we have to on 272 coil. Maybe he will tell us.
Wonder why others dont try this? Is it because of the cost of OEM 395 coils?
Pic just G3120 afm. 272 afm (needs ground to clear and didnt go past 10.7K.
395 coil is drop in on clone 3120 and later oem. No grind to fit like 272 coil. 395 coil has a free advance to it. So no messing with flywheel if wanted some.
Ethan 395 coil has more advance over the 272 coil. Few degrees
My oem stock one with jred aka 272 coil and non H side was 13.1K back in day.
The ported one with H side and 272 I always tuned it for working around 12K 44" 60" 72" for local till I ended up with it.
-
G3120 not hitting that limiter anymore.
Playing around to check it 3/8 8.
-
Farmertec 3120 with full skip 3/8.
135DL 42” bar and 3/8 8 rim leaves plenty adjustment. 😎
-
Mamma said get what you want for Fathers day. 😁
So after seeing guy in CRG using the cheap 36" bar he was running. I ordered me a 42" for use for stumping and big cuts.
Plus ordered it in 3/8 058 since I have 2 rolls of it here already to make my own 135DL chains with.
Also got a Farmertec G2511 Joncutter coming. Another 2511 echo clone for 99 shipped from US warehouse. Cheap as I have seen the echo clones.
Already have all the set up on hand too. .325 Nano, 1/4" mini micro, 3/8LP
-
ut a Denso plug in the G3120 since those NGK China made plugs can be hit and miss sometimes. Yes OEM made right there. ;)
-
Talking with Walt - I was just telling Kevin that. How my wants have changed. Old days H side and unlimited 272 coil. Today limited coil and no H dont bother me as to me a stumper.
Milling guys might want to be able to tune etc though.
I went to 3/8 8 from get go with short 32" bar.
-
https://youtu.be/pyPYqBOCZ5w
-
No slowing that down with 3/8 8 and short 32" bar.
-
Looks like Walter got one too.
https://youtu.be/gZZKBZaZmAE
-
Super nice. Easy to start. Fit and finish so nice.
-
Farmertec G3120 right now $330 and boat shipping is $100. Thats with tariff tax added in they say.
-
@Cut4fun . We don't have the bigger saws here in India, Maybe 660s a few but with 18" being the standard/accepted bar length here it the below 80cc saws that are in use here. No heavy logging, So no need for the bigger saws. But does the 3120 have an outboard clutch or an inboard clutch? And, does it run 404 or 3/8 chain normally?
Additionally Stihl and Husky have knocked the prices, plus they are registered for the government subsidy scheme of 50% which make them cheaper than clone saws. And the price knockdown is also on spares and accessories, nearly 30% on spares and 50% on accessories
-
@joe_indi has Farmertec released the G3120 3120 clone for sale in India or Indonesia yet?
Dealer pre buys been going on for a bit now.
-
Farmertec G3120 their selling.
First way at least. Bet more colors to come as is the clone world.
-
If you look close it appears fully adjustable carb too. I figure it will be rev limited like the G888 was and oem saws are. But if right set up 272 coil fixes that.
G888 361 coil fixed that one.
-
Farmertec G3120
Holzfforma 3120
One early pic when parts were bare.