Chainsaw Repair
Husqvarna - Stihl - Poulan - Jonsered - Dolmar chainsaws and more => Poulan => Topic started by: Cut4fun . on June 12, 2015, 02:56:54 pm
-
Poulan METAL YELLOW clutch cover.
So they are out there to my surprise. sweeeeeeeet ;D
Other thread on the jonsered 2083 2077 metal clutch cover http://chainsawrepair.createaforum.com/jonsered/clutch-cover-2077-2083-2083ii/msg25359/#msg25359
PB blocked pics :P
-
I will be hanged. Never knew they made them in mag. Thanks for showing that.
-
I will be hanged. Never knew they made them in mag. Thanks for showing that.
I just checked and the yellow one has the same number that the red one did inside ( of the top of my head 503 84 34 ) . Must be later saws in series I guess like Spike was talking about updated.
Another weird thing was the bar nuts are big around like the stihl ones.
-
Just seen this jonsered 2083 clutch cover. It appears to be a metal one like the NOS jonsered one I have. But if you notice it has the poulan pro or partner yellow underneath.
I never seen a partner metal clutch cover yet. So probable PP yellow.
-
Looks like I forgot to put the NOS ones here. poulan metal clutch covers for 415 425 445 475 505
-
Just saw this one today being sold on a poulan 475 for sale.
Appears to be a yellow metal clutch cover.
-
It will be interesting to see what that saw goes for.
-
Just showing middle 3 were the metal clutch covers used on the series. Outer 2 were plastic the more common ones used.
plastic 505 etc, NOS poulan, used came off PP445, NOS jonsered 2077 2083, plastic 505 etc
-
For you folks that use these saws still. Least this way if you have them for collecting you can save your plastic cover if your not lucky enough to have the oem metal ones.
Here is another idea I tried yesterday after seeing and running the 415 race saw with one, but with back half cut off.
I wasn’t going to do it. The 372 side tensioner cover was just to different.
But curiosity was killing me to know if I could make it work leaving the back half there. 372 side tensioner clutch cover with hand piece grinder used on it use on the partner poulan jred saws. Used double cut and cut off. Not perfect by any means. But now you can have side tensioner use these when nla covers can’t be found.
Imo front 268 etc cover still fit best. Now to test cut. Pic of the first one I did using those. All done by hand and hand pieces on grinder head.
-
I am still using the husky clutch cover on my milling saw. Poulan 505.
-
I was able to watch the chip flow today with 20" buried 71cc. Good to go with the side tensioner 372 clutch cover.
Had to throw the FD 415 ventmaster recoil cover on with it's D-ring for quick testing. Broke the rope 3rd pull on on other one.
-
Running low on stock so even picking up the plastic covers agin.
Poulan 475 clutch cover.
-
If anyone has a source for a clutch cover for a 445, please let me know
-
If anyone has a source for a clutch cover for a 445, please let me know
You get your Biden bucks? Going to need it.
I have a usable one with 475 on it.
I might put on a 445 of mine. But I am ok running a 372 or 272 modded covers on mine.
I have a yellow plastic and a even pricier red metal. Neither are cheap.
You the guy that ask me on FB group?
-
Used plastic yellow. Make sure you run the metal inner plates with these covers. 506093101 506 09 31 01
-
The later metal ones jonsered in red and poulan used in yellow.
-
First NOS plastic clutch cover I have found in this series . Usually metal ones in NOS. But figured better grab it.
-
I am surprised you found that clutch cover. Good find.