Recent Posts

Pages: 1 [2] 3 4 5 6 7 ... 10
11
Poulan / Poulan 3700 piston crown thickness
« Last post by Cut4fun on February 21, 2026, 07:39:10 am »
Never ever measure that area on these.

Pic of it?  So it is thin ring piston right?  3800 is thick and matters for which cylinder they can go in.

3700 p I sold to a guy. No none left just in a runner.



12
Stihl / Broken starter spring / 020avp
« Last post by jcsmith on February 20, 2026, 05:32:19 pm »
 A couple inside turns of the rewind spring broke off . Has anyone ever tried to heat up the end and try to reform it? I hate to **** away money if I don't have to.

Chris
13
Poulan / Poulan 3700 piston crown thickness
« Last post by jcsmith on February 20, 2026, 05:25:09 pm »
I used a screw in piston stop to remove the clutch and it left a divot in the center of the crown. Anyone know how thick the crown is and whether the piston can handle it? I used to stuff a starter rope thru the spark plug hole , but I'm thinking a stihl locking strip might be a better idea. What do you all use?

Chris
14
Poulan / Re: Poulan 415 425 445 475 505 jonsered 2077 2083 2083II Partner 660 710 7700 worm gear
« Last post by Cut4fun on February 20, 2026, 09:12:48 am »
Sent last of my oilers and 1 metal worm gear to Ireland. 

Have 1 used worm gear and 3 475 415 pto seal left.   

1-2 newer plastic used worm gears left. 1 both sides good 1 1 good side. 505 445 425

15
Husqvarna / Re: Husqvarna 564xp fuel Injection
« Last post by Cut4fun . on February 20, 2026, 08:25:31 am »
https://youtu.be/53Yd_B-dTtM
16
McCulloch / Re: Mcculloch 1-70
« Last post by Cut4fun . on February 19, 2026, 03:43:51 pm »
@heimannm   dang he is here too.
17
McCulloch / Re: Mcculloch 1-70
« Last post by ray benson on February 19, 2026, 11:33:30 am »
 Arboristsite forum. Look up heimannm. He is a McCulloch guru. Has a McCulloch shop/ museum in Iowa.
18
McCulloch / Re: Mcculloch 1-70
« Last post by Cut4fun . on February 19, 2026, 06:56:42 am »
I know nothing about macs.

But here is the collectors website run by a Magnus from Sweden. 

Searching 1-70 came up with 344 matches talking about them.

Bet they know a thing or 2.  http://www.chainsawcollectors.se/phpbb3/search.php?keywords=1-70
19
McCulloch / Mcculloch 1-70
« Last post by scratchy on February 18, 2026, 03:40:37 pm »
Finally got some time to tinker with the new acquisition today. So I have few question about this saw.  After the clean up I am wondering how many different models were produced of this saw as mine does not look like those listed on the IPL  that I received from Raymond. Thanks again Raymond. Also the gas tank has a preformed liner that looks like a scotch brite pad. It looks like it should be there, however I have never see anything like that in a gas tank.
20
Mowers Tillers Tractors etc / Re: Yardman 50" MTD
« Last post by Cut4fun . on February 18, 2026, 10:11:15 am »
I had to know where that other spring goes.  I found it in IPL.

OK I totally f'ed that up myself. 932-0209 dont show any where near the spring I thought I ordered.

So all on me. Just wow. SMH 

Pages: 1 [2] 3 4 5 6 7 ... 10