Author Topic: cs2240s wont start  (Read 3154 times)

0 Members and 42 Guests are viewing this topic.

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: cs2240s wont start
« Reply #30 on: February 07, 2016, 10:08:44 am »
It sounds like it could be the carburetor.   Try adjusting the L side out by half a turn and then see if there is any improvement.   The H is for wide open throttle and the L is for idle and transition to WOP.   If you get it to rev then make sure you adjust the H for the 4 stroking sound at WOP throttle and then when you put it in wood it will smooth out to 2 stroking.   

If the carb adjustments have no effect then you must have an air leak in it somewhere and you need to start checking things.
PP 505, 475, 445.

Offline trigger07

  • 3 cube
  • *
  • Posts: 18
  • Karma: 0

  • Total Badges: 8
    Badges: (View All)
    10 Posts Level 2 Combination Topic Starter Level 1 First Post
Re: cs2240s wont start
« Reply #31 on: February 07, 2016, 10:20:11 am »
hi thanks for your info there is only one adjustment screw and that only does the tickover there are openings for the other adjustment you mention but there are no screw visible to adjust

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: cs2240s wont start
« Reply #32 on: February 07, 2016, 10:38:07 am »
Well not all carbs have both adjustments.  Most of them do but sounds like yours does not.     The main thing is that your saw sounds like it has a lean condition not enough fuel.   It is either the carburetor or it is a air leak causing it to be lean.
PP 505, 475, 445.

Offline trigger07

  • 3 cube
  • *
  • Posts: 18
  • Karma: 0

  • Total Badges: 8
    Badges: (View All)
    10 Posts Level 2 Combination Topic Starter Level 1 First Post
Re: cs2240s wont start
« Reply #33 on: February 07, 2016, 10:41:58 am »
hi thanks i will take the carb of again and have a look to see if i can spot anything thanks a lot

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: cs2240s wont start
« Reply #34 on: February 07, 2016, 12:22:21 pm »
hi thanks for your info there is only one adjustment screw and that only does the tickover there are openings for the other adjustment you mention but there are no screw visible to adjust

On you carb the adjustment that is closet to the intake is the low the one closet to the air filter would be where the Hi would be.   If there is a adjustment there for the L I would still turn it out ccw by half a turn and see if the saw runs any better.
PP 505, 475, 445.

Offline trigger07

  • 3 cube
  • *
  • Posts: 18
  • Karma: 0

  • Total Badges: 8
    Badges: (View All)
    10 Posts Level 2 Combination Topic Starter Level 1 First Post
Re: cs2240s wont start
« Reply #35 on: February 11, 2016, 06:37:49 am »
hi to you all that gave me some great advice on my saw i finaly got it goin correctly today i took the carb back of and checked the seal but couldnt find any obstruction cleaned it up and refitted it and runs perfect now many thanks to all yours trigger

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: cs2240s wont start
« Reply #36 on: February 11, 2016, 11:17:11 am »
That is great.
PP 505, 475, 445.

 

Related Topics

  Subject / Started by Replies Last post
4 Replies
1021 Views
Last post January 05, 2012, 08:44:51 am
by Al Smith
5 Replies
820 Views
Last post December 06, 2013, 07:42:56 pm
by Al Smith
80 Replies
4809 Views
Last post February 13, 2014, 02:37:33 pm
by mastercraftka
5 Replies
452 Views
Last post January 09, 2014, 08:55:36 am
by sharkey
19 Replies
1173 Views
Last post February 21, 2014, 08:16:06 pm
by jmester
MS360 Pro wont start

Started by ears54 « 1 2 » Stihl

10 Replies
1359 Views
Last post August 16, 2015, 03:37:13 pm
by Cut4fun .
2 Replies
495 Views
Last post September 12, 2015, 09:44:05 pm
by jrdplowing
2 Replies
619 Views
Last post December 30, 2015, 03:58:15 pm
by Cat-Face Timber
4 Replies
1405 Views
Last post November 27, 2016, 08:59:14 pm
by mdavlee .
11 Replies
3717 Views
Last post June 05, 2017, 02:48:32 pm
by 3000 FPS