Author Topic: 3120  (Read 916 times)

0 Members and 19 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: 3120
« Reply #10 on: January 01, 2012, 06:45:07 pm »
Just this week I seen someone posting pics of their suppose to be  work of a open transfer with the tiny holes drilled in transfer to hold the JB and it looks just like MVP's work to me. Least it looked just like the MVP166 I had, MVP5000 and MVP2100 I seen inside of.

 I have  seen and known  really low people regrettably.

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 637
  • Karma: 80

  • Total Badges: 32
    Badges: (View All)
    Level 6 Linux User Mobile User Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary
Re: 3120
« Reply #11 on: January 01, 2012, 08:46:36 pm »
lots of people drill holes but very few port as nice as  he did , I put very few pictures of my porting on the internet and I feel for a very good reason

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181

  • Total Badges: 34
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 6 Seventh year Anniversary Sixth year Anniversary
Re: 3120
« Reply #12 on: January 01, 2012, 08:51:07 pm »
Oh I'd wager that even if the exact numbers were published with the time area open parameters,a detailed picture etc that no two people would have the same results .

I get a charge out of "numbers" because they mean nothing if the rest of the formula were not incorperated .

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 637
  • Karma: 80

  • Total Badges: 32
    Badges: (View All)
    Level 6 Linux User Mobile User Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary
Re: 3120
« Reply #13 on: January 01, 2012, 11:32:00 pm »
Yes  Al but to some ones eye that has ported alot of motors you can guess very close with out numbers just by looking at a  jug that has been ported , and race jugs are even easier cause with the transfer bridges cut out you know the step in is just above where the ring comes down to but does not touch it so you got a point to judge the rest of the ports by , If you see the piston then you know how wide  the ports are going to be and if they used a 4 mm corner or 5 mm corner on the ports , you can tell alot by looking at a picture

 

Related Topics

  Subject / Started by Replies Last post
0 Replies
339 Views
Last post May 13, 2012, 01:55:43 pm
by Cut4fun .
Husqvarna 3120

Started by Cut4fun . « 1 2 ... 9 10 » Husqvarna

91 Replies
6950 Views
Last post December 11, 2021, 11:43:43 am
by Cut4fun .
3120 big bore kit

Started by mcbob « 1 2 ... 6 7 » Husqvarna

65 Replies
4822 Views
Last post October 21, 2013, 07:35:51 pm
by mcbob
26 Replies
2980 Views
Last post May 16, 2016, 09:03:07 pm
by Cut4fun .
13 Replies
656 Views
Last post May 28, 2016, 10:25:26 am
by Cut4fun .
22 Replies
1225 Views
Last post August 17, 2017, 07:04:48 pm
by Cut4fun .
1 Replies
498 Views
Last post April 19, 2017, 03:25:32 pm
by Cut4fun
6 Replies
604 Views
Last post July 30, 2019, 12:55:35 pm
by Cut4fun .
0 Replies
416 Views
Last post March 22, 2021, 11:21:45 am
by Cut4fun .
5 Replies
1626 Views
Last post November 06, 2022, 07:50:51 am
by Cut4fun .