Author Topic: It's yellow but what is it?  (Read 1200 times)

0 Members and 0 Guests are viewing this topic.

Offline fordfairlane78

  • 6 cube
  • ****
  • Posts: 160
  • Karma: 16
  • Location: Valley Center,KS
Re: It's yellow but what is it?
« Reply #10 on: August 12, 2013, 01:41:00 am »
I have the same saw as yours tommysp1 for sale in husqvarna orange, a 34deluxe. Also saw a jred version of it pop up on ebay. I guess the question isn't who used this saw under their name but who didn't?!!!!
Trapped in time, surrounded by evil, low on gas

Offline tommysp61

  • 4 cube
  • **
  • Posts: 37
  • Karma: 3
Re: It's yellow but what is it?
« Reply #11 on: August 12, 2013, 09:58:06 am »
The local saw shop has a frontier a pioneer a skil  and a husqvarna same body with the one piece handle tank cover all of the part numbers are 507 which is pioneer they are a odd little saw Tom

Offline mikehonda

  • 4 cube
  • **
  • Posts: 51
  • Karma: 5
Re: It's yellow but what is it?
« Reply #12 on: September 09, 2015, 10:16:15 pm »
It look partner or skil or remington, i dont know i give up, allis chambers?

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2037
  • Karma: 199
  • Magnesium and Iron.
  • Location: Northern California.
Re: It's yellow but what is it?
« Reply #13 on: September 09, 2015, 10:23:12 pm »
That's a Frontier/Quadra/EMAB built saw.  Sold under the Skil, Husqvarna, and many other brand names.  There were many variants of them.  Some with AV.  Some with manual oilers.  Some with a weird ventilated clutch cover/exhaust duct setup (with a 'fan' setup on the clutch like what you'd see on a flywheel).  I don't like any of them.  Have had about 10 pass through my shop and have not kept any of 'em.  Gimme a Poulan Micro series saw over them any day of the week (and twice on Sunday)...
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline RoyM

  • Gas Hotsaw
  • ******
  • Posts: 502
  • Karma: 45
  • Location: Surrey British Columbia
Re: It's yellow but what is it?
« Reply #14 on: September 09, 2015, 11:19:11 pm »
I don't know what you guys are talking about. I have a Husky 35, possibly one of the last built because it has a chain brake, and is one of the easiest mini saws I have ever seen to work on. Remove the air filter, a bar nut, 3 screws and everything is exposed. Years ago a local r/c guy was buying them, it was the only engine in that class that was reliable enough for his application.
Old age and treachery always overcome youth and enthusiasm

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2037
  • Karma: 199
  • Magnesium and Iron.
  • Location: Northern California.
Re: It's yellow but what is it?
« Reply #15 on: September 10, 2015, 02:51:58 pm »
There has been a commercially available R/C version of the little Quadra engine available since about 1980 or so.  That was one of the first OPE based large scale engines on the market.  As the large scale market has grown, the list of gas engine mfgs has grown with it.  OPE based and purpose built large scale and giant scale engines abound.  There's also many folks out there (and here on this board) that covert various OPE engines for RC use.

Fixed the minor issue by changing four letters.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 18153
  • Karma: 345
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: It's yellow but what is it?
« Reply #16 on: September 10, 2015, 03:07:14 pm »
Was watching a show from abroad and funny how words in different places mean different things. I really liked their meaning of root in the show.

Hey girl you want to go root. ;) Sounds so much better then our F bomb.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
21 Replies
2138 Views
Last post March 12, 2016, 05:14:26 am
by Al Smith
8 Replies
1389 Views
Last post August 15, 2012, 01:51:39 pm
by Cut4fun .
77 Replies
657 Views
Last post February 16, 2017, 08:59:51 pm
by stubnail67