Author Topic: Poulan 330 3450  (Read 20247 times)

0 Members and 92 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan 330 3450
« Reply #370 on: September 19, 2017, 08:04:18 pm »
So where is the after pic.

Picture a 330 with no covers, no clutch cover, borrowed recoil since other one needs rope still. No air filter etc installed.
 Bare min to make sure she fired off and take throttle etc.  Will button  it up later on.

Couldnt get the dang plug out. Had to wait till warmed up then tried again with big hammer tapping srench.  Crazy tight  :o. Thought was going to break new av's   :D
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan 330 3450
« Reply #371 on: September 21, 2017, 02:23:07 pm »
So where is the after pic.

Picture a 330 with no covers, no clutch cover, borrowed recoil since other one needs rope still. No air filter etc installed.
 Bare min to make sure she fired off and take throttle etc.  Will button  it up later on.

Couldnt get the dang plug out. Had to wait till warmed up then tried again with big hammer tapping srench.  Crazy tight  :o. Thought was going to break new av's   :D

Still no time to button up this project.  Snapped a pic going by it.  ;)


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan 330 3450
« Reply #372 on: September 21, 2017, 05:35:33 pm »
So close.  I put that big oem dawg on it with the 22" bar they were sold with and a windsor chain. 
Forgot to check clutch drum bearing and it was bad. Pulled clutch off and put new bearing and grease. Then dinner bell rang.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan 330 3450
« Reply #373 on: September 21, 2017, 07:03:27 pm »
Done and tested. Just need to put rope in the other recoil.  Different clutch cover.

Took the tube out of the inside of the muffler on these.  Didnt drill this baffle out yet. Just removed screen.

Max is 13.8K but 12.8K was to my liking.



Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan 330 3450
« Reply #374 on: September 22, 2017, 01:29:01 pm »
I get ask this. So I am going to save it here and my website.  Off hand I know the poulan pro 330 380 and poulan 3450 3750 use this style pulley.

poulan 330 380 3450 3750 starter rope replacement.

Like Like x 1 View List

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4706
  • Karma: 320
  • Location: Carpenter, Wyoming

  • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Poulan 330 3450
« Reply #375 on: September 28, 2017, 08:58:07 pm »
I bought a parts saw 330, just so I could get the starter pulley and a few other parts for the intake when I was converting the 3500 over to the bigger carb.
The starter pulley I used on one my 3750 BB.
PP 505, 475, 445.
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan 330 3450
« Reply #376 on: September 28, 2017, 09:02:26 pm »
Thats why I keep buying up the parts saws too. But most of them are making it back to running status.

Offline drumbum

  • 4 cube
  • **
  • Posts: 48
  • Karma: 10

  • Total Badges: 19
    Badges: (View All)
    Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Level 4 Sixth year Anniversary Topic Starter
Re: Poulan 330 3450
« Reply #377 on: September 30, 2017, 08:30:13 pm »
Pick up my 3rd 330 yesterday.  New condition minus clutch and cover/brake, bar and chain.  Modded dogs and muffler this AM.
I can only guess the story with this saw, parts robbed at a dealer...warranty exchange?  Clean filter and spark arrestor, clean,clean, clean.  Could not have been run 10 mins at the outside. 

Purchased it for $30, put a clutch and a .325 8 rim and a 20" bar from a 2046 and a 330 brake/cover from a parts 330 i had and I'm grinning!  And apparently I have a surplus of ands I need to use before they go bad.

Has a tendency, unlike my others to run on high speed fresh out of a cut.  I'll give it some runtime before sorting that issue.

Planning to reuse the previously ported cylinder off one of my others that have both been converted to 60cc's and drop down to an 18" bar.

The saw had these stickers removed, starter -13,800 max - engine specs - and saftey crap at rear handle.

This one was like taking a walk and discovering a couple franklins stuck to your shoes.
Like Like x 2 View List

Offline drumbum

  • 4 cube
  • **
  • Posts: 48
  • Karma: 10

  • Total Badges: 19
    Badges: (View All)
    Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Level 4 Sixth year Anniversary Topic Starter
Re: Poulan 330 3450
« Reply #378 on: October 01, 2017, 08:44:43 am »
Anyone have a guess as to why I can't log in to AS?

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4666
  • Karma: 216
  • OHIO REDNECK

  • Total Badges: 44
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 7 Seventh year Anniversary Apple User
Re: Poulan 330 3450
« Reply #379 on: October 01, 2017, 09:07:54 am »
Anyone have a guess as to why I can't log in to AS?
Just went there. Its up.

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
1039 Views
Last post February 03, 2013, 06:33:10 pm
by 660magnum
Poulan 3450 60cc

Started by Cut4fun . « 1 2 ... 6 7 » Poulan

66 Replies
4075 Views
Last post February 08, 2018, 07:01:11 pm
by 3000 FPS
16 Replies
2737 Views
Last post April 11, 2014, 07:03:51 am
by Tractorsaw1
Poulan 3450 Carb issues

Started by rockfishon « 1 2 ... 7 8 » Poulan

77 Replies
3158 Views
Last post August 27, 2015, 07:55:47 pm
by Eccentric
5 Replies
898 Views
Last post October 23, 2014, 06:53:51 pm
by Cut4fun .
120 Replies
5375 Views
Last post October 07, 2023, 08:09:15 am
by Cut4fun
16 Replies
969 Views
Last post May 17, 2015, 10:00:49 am
by Cut4fun
2 Replies
594 Views
Last post March 20, 2015, 10:16:41 pm
by 3000 FPS
8 Replies
785 Views
Last post June 05, 2015, 09:52:30 am
by Cut4fun .
2 Replies
444 Views
Last post February 28, 2018, 01:25:07 pm
by Cut4fun .