Author Topic: MS200T Weight PHO.  (Read 257 times)

0 Members and 2 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2061
  • Karma: 205
  • Magnesium and Iron.
  • Location: Northern California.
MS200T Weight PHO.
« on: January 30, 2014, 08:07:33 pm »
Hello,

Any of you folks weigh an MS200T (PHO, and empty)?
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Social Buttons


Offline blsnelling

  • 4 cube
  • **
  • Posts: 58
  • Karma: 7
Re: MS200T Weight PHO.
« Reply #1 on: January 31, 2014, 08:47:24 pm »
I don't have a 200T weight, but here's a 201T.


Here's a MS150.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2061
  • Karma: 205
  • Magnesium and Iron.
  • Location: Northern California.
Re: MS200T Weight PHO.
« Reply #2 on: January 31, 2014, 08:54:14 pm »
Thanks Brad.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 18587
  • Karma: 362
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: MS200T Weight PHO.
« Reply #3 on: January 31, 2014, 08:56:46 pm »
Liking the weight of that 150. Brad what was the pho weight of that echo 271 you compared 150 to?
REDNECK Saw Repair Getter Done

Offline winland

  • 6 cube
  • ****
  • Posts: 215
  • Karma: 24
  • Location: 44883
    • Winland Boxers
Re: MS200T Weight PHO.
« Reply #4 on: January 31, 2014, 10:01:57 pm »
I can get you the weight of my 200t in the morning.
Do not have my britches on and not going out there tonight.
Brrrrrrr COLD

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2061
  • Karma: 205
  • Magnesium and Iron.
  • Location: Northern California.
Re: MS200T Weight PHO.
« Reply #5 on: January 31, 2014, 10:19:08 pm »
I can get you the weight of my 200t in the morning.
Do not have my britches on and not going out there tonight.
Brrrrrrr COLD


Thank you.  Tomorrow will be great.  No need to freeze your important stuff tonight.:D
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline winland

  • 6 cube
  • ****
  • Posts: 215
  • Karma: 24
  • Location: 44883
    • Winland Boxers
Re: MS200T Weight PHO.
« Reply #6 on: February 01, 2014, 09:23:57 am »
My digital bathroom scale says 8.4#  dry weight
You could probably take a couple ounces of sawdust/grime off and some residual bar oil.
Plus a bit of black tape around the handle.
My Stihl 200T owners manual says it should be 7.9#
The chart on "Bill's Saw Shop" calls out 7.7#
Hope this helps.


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 18587
  • Karma: 362
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: MS200T Weight PHO.
« Reply #7 on: February 01, 2014, 11:13:21 am »
I had read the 200 was 60grams less then the 201 dry new PHO saws. So that makes the oem book specs wrong again and your scale pic about dead on to 201 pic above.

60 grams = 0.132277lb
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2061
  • Karma: 205
  • Magnesium and Iron.
  • Location: Northern California.
Re: MS200T Weight PHO.
« Reply #8 on: February 01, 2014, 05:58:56 pm »


Thanks for weighing your saw and posting the pic!
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 18587
  • Karma: 362
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: MS200T Weight PHO.
« Reply #9 on: February 05, 2014, 03:55:58 pm »
Stihl 200t weight PHO
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
7 Replies
746 Views
Last post June 23, 2012, 10:24:43 pm
by mdavlee
4 Replies
203 Views
Last post November 23, 2014, 03:36:23 pm
by Cut4fun .
3 Replies
291 Views
Last post November 15, 2014, 05:53:48 pm
by Eccentric
7 Replies
528 Views
Last post August 03, 2014, 09:11:26 pm
by Cut4fun .
0 Replies
94 Views
Last post February 06, 2014, 12:48:22 pm
by Cut4fun .
4 Replies
150 Views
Last post December 08, 2014, 10:22:53 pm
by 3000 FPS
5 Replies
142 Views
Last post January 03, 2015, 08:46:14 pm
by Cut4fun .
2 Replies
218 Views
Last post March 28, 2015, 09:29:02 pm
by Cut4fun .
0 Replies
28 Views
Last post October 03, 2016, 02:31:15 pm
by Cut4fun
0 Replies
17 Views
Last post September 10, 2017, 08:43:58 am
by fisaw