« previous next »
Pages: 1 ... 4 5 6 7 8 [9]   Go Down

Author Topic: Husqvarna 372 XP  (Read 18520 times)

0 Members and 43 Guests are viewing this topic.

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: Husqvarna 372 XP
« Reply #80 on: February 17, 2013, 08:11:32 pm »
I have 372's set up all these different ways and have no intention of changing any of them.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • 4 cube
  • **
  • Posts: 50
  • Karma: 5

    • Total Badges: 12
    Badges: (View All)
    One year Anniversary Level 3 50 Posts Karma 10 Posts Level 2
Re: Husqvarna 372 XP
« Reply #81 on: February 17, 2013, 10:57:33 pm »
It's pre-2007, just thinking that maybe the latter set up for the vent was better then the pre 07 stuff.
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: Husqvarna 372 XP
« Reply #82 on: February 17, 2013, 11:04:43 pm »
See if that elbow with fit and stay in your existing stand pipe?

You could even take your existing carb floor and drill two holes in it to loop a piece of Tygon off the elbow and up through the floor to form a secondary air loop.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • 4 cube
  • **
  • Posts: 50
  • Karma: 5

    • Total Badges: 12
    Badges: (View All)
    One year Anniversary Level 3 50 Posts Karma 10 Posts Level 2
Re: Husqvarna 372 XP
« Reply #83 on: February 17, 2013, 11:15:44 pm »
I see that there is a punch out spot on the carb base plate next to the fuel line punch out.  Might work.
I will have to figure out if the elbow will fit in the hole, it's about a M5 bolt size for 4-6 cm deep, the it steps down in size, must have some sort of ring or seal to hold it in.
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: Husqvarna 372 XP
« Reply #84 on: February 17, 2013, 11:25:07 pm »
The elbow has some coarse plastic threads on the end that goes up in the tank.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • 4 cube
  • **
  • Posts: 50
  • Karma: 5

    • Total Badges: 12
    Badges: (View All)
    One year Anniversary Level 3 50 Posts Karma 10 Posts Level 2
Re: Husqvarna 372 XP
« Reply #85 on: February 26, 2013, 09:24:02 pm »
Vent for the carb is done, saw is running great!   I might take it in and see if they will do a compression test just to see.  Anyway thanks again for the help with project. 
Logged
Pages: 1 ... 4 5 6 7 8 [9]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
2 Replies
4661 Views 		Last post March 04, 2012, 02:35:58 pm
by Cut4fun .
6 Replies
4617 Views 		Last post June 27, 2017, 08:30:17 pm
by Cut4fun .
7 Replies
6107 Views 		Last post January 31, 2016, 12:49:24 pm
by 660magnum
0 Replies
1546 Views 		Last post March 30, 2016, 07:10:38 pm
by mikehonda
4 Replies
3307 Views 		Last post April 12, 2016, 06:30:34 pm
by dannyupsolate
4 Replies
4106 Views 		Last post November 07, 2016, 05:46:56 pm
by oldpro
2 Replies
3839 Views 		Last post May 15, 2016, 04:59:09 am
by Eccentric
21 Replies
11586 Views 		Last post May 22, 2024, 07:32:41 am
by Cut4fun
4 Replies
3923 Views 		Last post November 23, 2016, 02:23:26 am
by georgehopson
1 Replies
2437 Views 		Last post October 26, 2016, 03:40:28 pm
by Eccentric