« previous next »
Pages: [1]   Go Down

Author Topic: husqvarna 445 fuel bulb replace  (Read 6218 times)

0 Members and 41 Guests are viewing this topic.

Offline

  • pruner
  • *
  • Posts: 2
  • Karma: 0

    • Total Badges: 7
    Badges: (View All)
    Level 2 Combination Topic Starter First Post Level 1 Search
husqvarna 445 fuel bulb replace
« on: November 05, 2013, 05:45:12 pm »
do I need to take the carb off the chainsaw to get the primer bulb ?
does anyone have the steps to replace the bulb?

thanks
gary
Logged

Share on Bluesky Share on Facebook

Offline

  • pruner
  • *
  • Posts: 2
  • Karma: 0

    • Total Badges: 7
    Badges: (View All)
    Level 2 Combination Topic Starter First Post Level 1 Search
Re: husqvarna 445 fuel bulb replace
« Reply #1 on: November 05, 2013, 08:39:57 pm »
ok, I figured it out
I took out the air filter and the 4 screws holding the black plate on the carb body. the loosed the plate enough to move it a little back out of the orange hole the primer bulb sits in and then I was able to see one of the barbed clips on the top side and took a small flat screwdriver and pushed down and out and it popped out with the 2 fuel lines attached. I used a small pair of needle nose pliers to gently pull the bulb out until I could grab the 2 fuel lines and pull them out enough to get both off the old bulb and replace with the new one. Once I figured it out it took maybe 2 minutes to remove the old and replace with the new one.

I probably didn't need to even remove the 4 screws after looking at that.
good luck
 
Logged

Offline

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4709
  • Karma: 320
  • Location: Carpenter, Wyoming

    • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: husqvarna 445 fuel bulb replace
« Reply #2 on: November 06, 2013, 07:57:16 pm »
Quote from: sasglm on November 05, 2013, 08:39:57 pm
ok, I figured it out
I took out the air filter and the 4 screws holding the black plate on the carb body. the loosed the plate enough to move it a little back out of the orange hole the primer bulb sits in and then I was able to see one of the barbed clips on the top side and took a small flat screwdriver and pushed down and out and it popped out with the 2 fuel lines attached. I used a small pair of needle nose pliers to gently pull the bulb out until I could grab the 2 fuel lines and pull them out enough to get both off the old bulb and replace with the new one. Once I figured it out it took maybe 2 minutes to remove the old and replace with the new one.

I probably didn't need to even remove the 4 screws after looking at that.
good luck
 

I hope you remember which fuel line went where on the purge bulb.   It makes a difference.   The bulb actually purges the air out of the lines and carburetor.
Logged
PP 505, 475, 445.
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
6 Replies
4679 Views 		Last post January 11, 2013, 05:01:34 pm
by Cut4fun .
3 Replies
2073 Views 		Last post October 06, 2013, 09:51:24 pm
by Eccentric
1 Replies
1360 Views 		Last post January 21, 2014, 10:12:33 pm
by Eccentric
8 Replies
2317 Views 		Last post March 12, 2014, 09:42:07 am
by KilliansRedLeo
10 Replies
3746 Views 		Last post April 16, 2015, 08:12:11 pm
by SawTroll
8 Replies
2295 Views 		Last post September 13, 2015, 02:47:57 pm
by jrdplowing
2 Replies
1911 Views 		Last post February 02, 2016, 07:30:39 pm
by Cycledude
2 Replies
1248 Views 		Last post July 17, 2016, 09:26:05 pm
by Nathaniel Vansickle
4 Replies
1148 Views 		Last post February 27, 2017, 05:53:53 am
by dmccann
2 Replies
138 Views 		Last post December 22, 2025, 11:48:24 am
by Dave588