Author Topic: Muffler mods (Read 7124 times)

doreadeal · « **Reply #20 on:** September 22, 2013, 08:34:01 pm »

Nice work on those mufflers! With stock mufflers (even modded) I can see the screen not changing much. The discharge port is almost always much bigger then the baffle port. Now if you were to make a muffler in witch the reflection pulse was done without the baffle, but rather on the outer can of the muffler, I could see a screen being harmful to output. My educated guess is that it would have a less then good effect on the reflected pulse and require more restriction of the discharge port. Just a guess...

Cut4fun . · « **Reply #21 on:** September 22, 2022, 10:52:29 am »

All chainsaws used on National Forests must
have an approved spark arrester (a stainless
steel wire screen in the muffler). The openings
in the screen must be .023 inches or less.
Forest officials may request a check of saws in
firewood cutting areas. Forest Service employees
are not allowed to take your saw apart so you
need to carry the tools needed to remove the
exhaust device and expose the spark arrester.
Certification is good for one year

3000 FPS · « **Reply #22 on:** September 22, 2022, 10:37:25 pm »

I cut in national forest every year all the time. Last year I felled around 33 trees in nation forest. Like you said better make sure those spark arresters are correct. Good info there.

Cut4fun . · « **Reply #23 on:** September 23, 2022, 11:18:42 am »

Quote from: 3000 FPS on September 22, 2022, 10:37:25 pm

I cut in national forest every year all the time. Last year I felled around 33 trees in nation forest. Like you said better make sure those spark arresters are correct. Good info there.

I was researching it for a guy wanting to do screen on a tube or pipe out the saws. I seen yours inside on yours and other guys showed me their on outer pipes.

I then looked up his area for cutting Oregon. They are even stricter then the USDA ones above. Almost to point need to be a stock saw. Says no mods to saws whatsoever.

pleasant · « **Reply #24 on:** September 24, 2022, 10:30:31 am »

Quote from: JOE.G on January 13, 2013, 07:02:39 am

I see you like to keep your screens in, Some people swear they restrict others say they don't.

If the screen is kept free of carbon build up, then there is nothing to gain performance wise by removing it. However they are prone to carbon clogging particularly if someone is using a low quality mineral based oil and/or a slightly richer mix ratio. Always worth removing every now and then to clean them out

3000 FPS · « **Reply #25 on:** September 24, 2022, 12:02:25 pm »

Quote from: Cut4fun . on September 23, 2022, 11:18:42 am

Quote from: 3000 FPS on September 22, 2022, 10:37:25 pm
I cut in national forest every year all the time. Last year I felled around 33 trees in nation forest. Like you said better make sure those spark arresters are correct. Good info there.

I was researching it for a guy wanting to do screen on a tube or pipe out the saws. I seen yours inside on yours and other guys showed me their on outer pipes.

I then looked up his area for cutting Oregon. They are even stricter then the USDA ones above. Almost to point need to be a stock saw. Says no mods to saws whatsoever.

Yes, I do like keeping the spark arrestors in the stock position if possible and really just open up the ports and baffles.

Subject / Started by	Replies	Last post
Dual port muffler mods, various. Started by alsled « 1 2 » Welding Shop	18 Replies 6673 Views	November 22, 2013, 09:55:56 pm by Al Smith
CS-400 Muffler Mod Started by huichex « 1 2 ... 5 6 » Echo	58 Replies 12416 Views	August 12, 2014, 11:41:26 pm by stubnail67
Muffler Mods Using Silver Solder Started by KilliansRedLeo « 1 2 3 » How To Basics and Fixes	28 Replies 4330 Views	December 22, 2013, 09:08:10 pm by KilliansRedLeo
Muffler Mods Started by The Ripper Poulan	7 Replies 4825 Views	January 19, 2014, 09:10:11 am by The Ripper
Dolmar PS-421 mods Started by Nathaniel Vansickle « 1 2 3 » Dolmar Makita	25 Replies 4078 Views	December 02, 2014, 12:17:05 pm by 7sleeper
Echo mods? Started by Jaymo Echo	7 Replies 1854 Views	October 24, 2017, 08:54:00 pm by Jaymo
CS 400 Muffler mod. Started by trail twister « 1 2 » Echo	10 Replies 1550 Views	October 30, 2017, 09:27:09 pm by trail twister
610 Muffler Started by dpjones « 1 2 » McCulloch	14 Replies 2701 Views	November 01, 2017, 09:56:43 am by Chris-PA
Poulan 3500/3750 mods Started by The Ripper « 1 2 » Poulan	16 Replies 6980 Views	February 03, 2024, 06:26:08 pm by The Ripper
Simple Mods to the Stihl FS55 Started by joe_indi Chainsaws not listed - Gas OPE	0 Replies 1346 Views	February 09, 2024, 12:41:23 pm by joe_indi

Chainsaw Repair

News:

Author Topic: Muffler mods (Read 7124 times)

doreadeal

Muffler mods

Cut4fun .

Re: Muffler mods

3000 FPS

Re: Muffler mods

Cut4fun .

Re: Muffler mods

pleasant

Re: Removing Spark Screens, Does it make a difference?

3000 FPS

Re: Muffler mods

Related Topics