« previous next »
Pages: [1]   Go Down

Author Topic: Poulan plastic tank  (Read 2218 times)

0 Members and 56 Guests are viewing this topic.

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Poulan plastic tank
« on: April 23, 2017, 01:39:54 pm »
Poulan plastic tank seal repair. 

Tank I was getting ready to ship. I like to plug them off and check for leaks.
There was a hair of seepage in the corner.  Not a leak as drips, just seepage making it moist over time if you know what I am trying to say.
So I went ahead and used the sealall tank sealant inside and out on that area.  I usually do the outside but was able to get to the inside corner too.
Going to let dry and test again after it gets set.
If you look how they are put together they are to pieces of plastic melted together by heat.

@ajdjrn

Logged

Share on Bluesky Share on Facebook

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan plastic tank
« Reply #1 on: April 23, 2017, 01:49:58 pm »
I always allow 24hrs before I check it after applying. Have used it on metal gas tanks etc in past years.

Seal-All
Seal-All is the adhesive mechanics and hobbyists trust for all their automotive and garage repairs. It adheres with superior strength to most substrates and resists gasoline, oil, paint thinner and most solvents.

• Fast dry time – set in 2-3 minutes
• E-Z flow formula
• Gas & oil resistant
• Waterproof – bond remains secure even when exposed to water
• Abrasion resistant
• Temperature resistant – remains tough even in extreme temperatures

Logged

Offline

  • 4 cube
  • **
  • Posts: 71
  • Karma: 18

    • Total Badges: 23
    Badges: (View All)
    Eighth year Anniversary Level 5 Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary
Re: Poulan plastic tank
« Reply #2 on: April 24, 2017, 07:12:13 am »
I used a soldering gun to "re-melt" the tank seam on a shinny 757, no more leaky!!....... ;)
Logged
Like Like x 1 View List

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan plastic tank
« Reply #3 on: April 24, 2017, 06:36:48 pm »
Quote from: old 040 on April 24, 2017, 07:12:13 am
I used a soldering gun to "re-melt" the tank seam on a shinny 757, no more leaky!!....... ;)

Most times I cant get a solder gun where I need to seal one.

Like this one I did today. Right under carb area at the seam under carb.  Poulan 3000 3.0 etc etc tank



Logged
Agree Agree x 1 View List

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan plastic tank
« Reply #4 on: April 25, 2017, 09:03:41 pm »
Fixed the last area that showed seepage in web area in front. Checked today and all good.

Now for a tank vent duckbill valve and brass cover by new owner and she will be ready to install on new owners 3750 Bad Boy saw. His green tank got smashed by a tree.

Logged

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan plastic tank
« Reply #5 on: April 26, 2017, 05:36:49 pm »
The black one under the carb area I just cant get it to stop seeping under there. Back on the shelf it goes for parts.

3 times now and jut cant get to that area.
Logged

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Poulan plastic tank
« Reply #6 on: November 24, 2023, 08:50:41 am »
3.3 type 2 tank. Pulled and stripped bare.

This is the later type 2 ones with tank vent on side and only 1 line for fuel out top. 1997.

This one also excepts the big intakes like used on 330 380 3750 3450 without modifications to tank hole.

Setting with mix testing.


Day 2  I figured it would pass setting over night. It did no mix leaked.

Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
0 Replies
1533 Views 		Last post November 06, 2011, 07:52:07 pm
by Cut4fun
11 Replies
2603 Views 		Last post November 01, 2012, 03:09:39 pm
by Cut4fun
6 Replies
2208 Views 		Last post July 29, 2015, 01:51:18 pm
by Chris-PA
1 Replies
2033 Views 		Last post February 09, 2017, 12:26:19 pm
by Cut4fun .
4 Replies
2486 Views 		Last post September 22, 2016, 07:36:10 pm
by mowertech
0 Replies
1522 Views 		Last post February 04, 2017, 10:29:55 am
by mowertech
5 Replies
1781 Views 		Last post July 05, 2017, 06:54:47 am
by mowertech
24 Replies
16811 Views 		Last post May 10, 2024, 02:33:45 pm
by Cut4fun .
0 Replies
1547 Views 		Last post November 25, 2020, 08:52:46 am
by Cut4fun .
0 Replies
1407 Views 		Last post August 29, 2023, 08:58:18 am
by Cut4fun .