« previous next »
Pages: [1] 2   Go Down

Author Topic: 066 recoil  (Read 8669 times)

0 Members and 63 Guests are viewing this topic.

Offline

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28

    • Total Badges: 18
    Badges: (View All)
    Third year Anniversary Karma Good Level 4 Second year Anniversary Poll Voter One year Anniversary
066 recoil
« on: September 21, 2015, 09:53:33 pm »
any tricks to get a worn recoil to engage better or more often.  need to crank this thing before i make parts order.
Logged

Share on Bluesky Share on Facebook

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

    • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: 066 recoil
« Reply #1 on: September 22, 2015, 12:15:08 am »
Probably needs new rope rotor and pawls. The sockets where the pawl pivots become sloppy and worn pawl tips lead to poor engagement.
Logged

Offline

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28

    • Total Badges: 18
    Badges: (View All)
    Third year Anniversary Karma Good Level 4 Second year Anniversary Poll Voter One year Anniversary
Re: 066 recoil
« Reply #2 on: September 22, 2015, 01:23:11 am »
yes  exactly  I put pawl back in straightened clip and got it to turn over a few times .   seems to have stopped engaging again now.
Logged

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: 066 recoil
« Reply #3 on: September 22, 2015, 12:32:59 pm »
I was thinking like Adam. Did you replace rotor too or just the pawls?  Rotor might be wallowed.
Logged

Offline

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28

    • Total Badges: 18
    Badges: (View All)
    Third year Anniversary Karma Good Level 4 Second year Anniversary Poll Voter One year Anniversary
Re: 066 recoil
« Reply #4 on: September 22, 2015, 01:22:15 pm »
was just trying to get it to start before I order parts.  trying to get everything in one order. no 066 parts on hand. will order complete recoil and housing since one screw boss is broke off bottom of recoil housing.
Logged

Offline

  • 5 cube
  • ***
  • Posts: 111
  • Karma: 23

    • Total Badges: 12
    Badges: (View All)
    Apple User Mobile User Combination Topic Starter Level 2 50 Posts
Re: 066 recoil
« Reply #5 on: September 22, 2015, 06:02:59 pm »
I keep a stash of starter pawls on hand.  Every one thru here gets new ones.
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2114
  • Karma: 172
  • Location: VA

    • Total Badges: 36
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 6
Re: 066 recoil
« Reply #6 on: September 23, 2015, 06:55:23 am »
I have mostly seen problems with the rotor. Becoming sloppy on the stud or axle in the cover.
Logged

Offline

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28

    • Total Badges: 18
    Badges: (View All)
    Third year Anniversary Karma Good Level 4 Second year Anniversary Poll Voter One year Anniversary
Re: 066 recoil
« Reply #7 on: September 23, 2015, 01:08:23 pm »
how many models of pawls are there.  can you just keep large and small on hand and cover most stihl models or are they model specific.
Logged

Offline

  • Piped Saw
  • *****
  • Posts: 309
  • Karma: 45

    • Total Badges: 21
    Badges: (View All)
    Level 5 Third year Anniversary Poll Voter 100 Posts Second year Anniversary Level 4
Re: 066 recoil
« Reply #8 on: September 23, 2015, 05:33:53 pm »
I have seen a slightly bent spring hold up the pawls from extending.
Make sure (while holding the assembly in your hand after removing from the saw) the little tabs on the pawls are inside the spring so when the rope is pulled, the spring directs the tabs on the pawls outward, without any hang up or hesitation
Logged

Offline

  • Piped Saw
  • *****
  • Posts: 328
  • Karma: 28

    • Total Badges: 18
    Badges: (View All)
    Third year Anniversary Karma Good Level 4 Second year Anniversary Poll Voter One year Anniversary
Re: 066 recoil
« Reply #9 on: September 23, 2015, 07:26:39 pm »
guys I think this rotor has all the problems you have mentioned at once. it 's done hurt my shoulder and customer can wait till new one gets here from china. maybe shoulder be better by then.  do the rotors interchange for several models or not.  might order some extra if they work on several models
Logged
Pages: [1] 2   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
3 Replies
1936 Views 		Last post March 17, 2013, 05:43:43 pm
by brokenbudget
10 Replies
6910 Views 		Last post October 30, 2013, 02:13:17 pm
by Cut4fun .
6 Replies
10295 Views 		Last post April 02, 2014, 09:15:00 pm
by JohnG28
0 Replies
1011 Views 		Last post July 07, 2015, 03:39:48 pm
by jmester
9 Replies
2642 Views 		Last post October 09, 2015, 03:04:41 pm
by aclarke
4 Replies
1963 Views 		Last post September 30, 2016, 09:51:10 pm
by jmester
3 Replies
1948 Views 		Last post January 02, 2018, 06:01:56 am
by trail twister
1 Replies
2255 Views 		Last post May 27, 2020, 11:08:46 am
by Cut4fun .
8 Replies
2807 Views 		Last post March 03, 2021, 09:32:40 am
by super44
1 Replies
2088 Views 		Last post October 11, 2022, 07:59:10 am
by Cut4fun .