« previous next »
Pages: [1]   Go Down

Author Topic: MS 241CM issue  (Read 1473 times)

0 Members and 63 Guests are viewing this topic.

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

    • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
MS 241CM issue
« on: January 31, 2016, 01:51:30 pm »
Just a heads up, some 241's have an improperly aligned intake boot from the factory. This does not give a proper seal where the impulse tube slides into the boot. We are fixing under warranty. 2 so far.
Logged

Share on Bluesky Share on Facebook

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: MS 241CM issue
« Reply #1 on: February 18, 2016, 07:05:12 pm »
Only issue so far?
Logged

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

    • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: MS 241CM issue
« Reply #2 on: February 19, 2016, 08:36:29 pm »
Our mechanic was off to Stihl tech school this week. The day was mostly on M-tropics. Didn't get to hear all that was discussed when he returned. One other thing that can be an issue is that the flywheel can get dirty enough to cause the saw to run poorly. Only 1 saw so far but it would not read on the diagnostic until poles were cleaned on flywheel.

My personal 241 has 70 plus tanks on it now. The best small wood pulp saw I have ever owned. My 261 just sets on the shelf now.
Logged

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

    • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: MS 241CM issue
« Reply #3 on: February 21, 2016, 01:21:50 pm »
Started to read some of the literature our tech brought back regarding the Stihl diagnostic tool. Seems it can be used to check for lean conditions on a tradition carb equipped saw. Will check into it more at work tomorrow.
Logged
Like Like x 1 View List
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
8 Replies
2531 Views 		Last post August 30, 2012, 12:53:08 pm
by Remington
22 Replies
4912 Views 		Last post January 24, 2016, 05:16:42 pm
by Reddog
5 Replies
3253 Views 		Last post January 25, 2014, 03:07:17 pm
by Infinitive
11 Replies
2195 Views 		Last post February 09, 2015, 09:32:54 pm
by DexterDay
6 Replies
1840 Views 		Last post May 19, 2015, 06:53:03 am
by Spike60
8 Replies
1519 Views 		Last post September 30, 2015, 09:14:25 pm
by jmester
0 Replies
992 Views 		Last post October 17, 2015, 03:31:43 pm
by jrdplowing
6 Replies
1609 Views 		Last post May 09, 2016, 05:25:47 am
by Al Smith
10 Replies
2003 Views 		Last post October 10, 2016, 08:25:35 am
by Old Iron Logging
3 Replies
824 Views 		Last post November 08, 2017, 11:05:17 pm
by super44