« previous next »
Pages: [1]   Go Down

Author Topic: ms 310 topend rebulit  (Read 1305 times)

0 Members and 50 Guests are viewing this topic.

Offline

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
  • its cold up here eh!!
  • Location: ontario canada

    • Total Badges: 7
    Badges: (View All)
    Search Level 2 Karma Topic Starter First Post Level 1
ms 310 topend rebulit
« on: January 06, 2014, 02:40:57 pm »
hey guys new to the form looks like a great site need some help just got a ms310 used    put half a dozen cuts on it and it ran alittle fun so took it to the local shop to get get it tuned up and the piston and cylinder r shot should I replace the bearings and oil seals well doing the job i'm up in Canada not sure where to get parts any advice will be great thanks  ???
Logged

Share on Bluesky Share on Facebook

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: ms 310 topend rebulit
« Reply #1 on: January 06, 2014, 02:59:55 pm »
Put a 390 engine unit in it? The same one fits the 290, 310, and 390.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
  • its cold up here eh!!
  • Location: ontario canada

    • Total Badges: 7
    Badges: (View All)
    Search Level 2 Karma Topic Starter First Post Level 1
Re: ms 310 topend rebulit
« Reply #2 on: January 06, 2014, 03:11:59 pm »
k ill look in it thanks 660
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: ms 310 topend rebulit
« Reply #3 on: January 06, 2014, 03:19:03 pm »
the carbs are the same on all those.

I don't know a good Canadian source but Ebay is full of after market engine units. They seem to hold up pretty well.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
  • its cold up here eh!!
  • Location: ontario canada

    • Total Badges: 7
    Badges: (View All)
    Search Level 2 Karma Topic Starter First Post Level 1
Re: ms 310 topend rebulit
« Reply #4 on: January 06, 2014, 03:20:09 pm »
will the carb set up be the same as the 310
 ???
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: ms 310 topend rebulit
« Reply #5 on: January 06, 2014, 03:20:39 pm »
yes
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: ms 310 topend rebulit
« Reply #6 on: January 06, 2014, 03:21:10 pm »
Here is what 660 is talking about  I think.   http://www.baileysonline.com/Chainsaws/Chainsaw-Parts/Short-Blocks/Shindaiwa/NWP-49mm-Short-Block-Cylinder-for-Stihl-Chainsaws-029-039-MS290-MS310-MS390.axd

Suppose to be bolt in ready to go.

Click on stihl board and look down a few threads where someone used one on a 290 build to 390.
Logged

Offline

  • 3 cube
  • *
  • Posts: 11
  • Karma: 1
  • its cold up here eh!!
  • Location: ontario canada

    • Total Badges: 7
    Badges: (View All)
    Search Level 2 Karma Topic Starter First Post Level 1
Re: ms 310 topend rebulit
« Reply #7 on: January 06, 2014, 03:22:24 pm »
k once again thanks ill take a look how much should it cost don't want to get screwed 
Logged

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: ms 310 topend rebulit
« Reply #8 on: January 06, 2014, 03:23:04 pm »
posted above your last post.
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
2 Replies
1848 Views 		Last post May 03, 2013, 06:59:36 am
by Spike60
13 Replies
2555 Views 		Last post August 14, 2013, 05:41:17 pm
by Cut4fun .
2 Replies
1097 Views 		Last post August 20, 2014, 11:50:25 pm
by stihls066
2 Replies
1182 Views 		Last post August 23, 2014, 06:13:55 pm
by Old Iron Logging
14 Replies
3020 Views 		Last post January 21, 2015, 08:32:45 pm
by Cut4fun .
0 Replies
663 Views 		Last post March 07, 2022, 01:49:52 pm
by Cut4fun .
4 Replies
2506 Views 		Last post April 04, 2022, 07:57:39 am
by Cut4fun .