« previous next »
Pages: [1]   Go Down

Author Topic: MS290 carb adjust after MM  (Read 1789 times)

0 Members and 1 Guest are viewing this topic.

Offline

  • 6 cube
  • ****
  • Posts: 215
  • Karma: 24
  • Location: 44883
    • Winland Boxers

    • Total Badges: 24
    Badges: (View All)
    Third year Anniversary Second year Anniversary One year Anniversary Level 5 100 Posts 50 Posts
MS290 carb adjust after MM
« on: October 27, 2013, 03:57:05 pm »
How do I remove the H & L limiters on my MS290?

Logged

Share on Bluesky Share on Facebook

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24887
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: MS290 carb adjust after MM
« Reply #1 on: October 27, 2013, 05:37:29 pm »
I  just use drywall screw.  Screw in pull quick and pops out most times. Sometimes it might not, so just repeat.
Logged

Offline

  • 6 cube
  • ****
  • Posts: 215
  • Karma: 24
  • Location: 44883
    • Winland Boxers

    • Total Badges: 24
    Badges: (View All)
    Third year Anniversary Second year Anniversary One year Anniversary Level 5 100 Posts 50 Posts
Re: MS290 carb adjust after MM
« Reply #2 on: October 27, 2013, 06:21:10 pm »
Thanks. 
I was not sure exactly what to do.
That did the trick.  Screwed in, pulled out.  No more limiters.

Insert ear plugs.
Pull cord.
A couple of tweeks and a check with the tach.
Another ajustment.
Yee Haa.
Logged

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4941
  • Karma: 216
  • OHIO REDNECK

    • Total Badges: 44
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 7 Seventh year Anniversary Apple User
Re: MS290 carb adjust after MM
« Reply #3 on: October 28, 2013, 12:59:24 pm »
Some folks state to reinstall the caps after adjusting to keep the screws from creeping.  The ones I have did for many firewood cutters and some of my own never had a problem with this. 

Just so you know if you notice anything changing.
Logged

Offline

  • 5 cube
  • ***
  • Posts: 100
  • Karma: 11
  • Location: Were the Pacific Northwest Soft Woods Grow

    • Total Badges: 19
    Badges: (View All)
    100 Posts Second year Anniversary Karma Good Level 4 50 Posts One year Anniversary
Re: MS290 carb adjust after MM
« Reply #4 on: October 28, 2013, 01:38:16 pm »
Another way is to use a drill and drill motor and drill the plastic till your hit metal than use screw it till you can get the plastic off the back of the screw

I haven't seen it come out of tune not having the plastic limiter on that screw
Logged
"People ask me where all my money went, I tell them half of it I spent on gambling, fast women and liquor, the other half I wasted!" W.C.

"..... nothing more funnier than watching some ole coot make a fool out of himself, especially sideways”

"You can't argue with someone that doesn't have any real life experience on the subject."

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: MS290 carb adjust after MM
« Reply #5 on: October 28, 2013, 02:01:25 pm »
I like leaving the limiters on but just removing the tabs from them.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2114
  • Karma: 172
  • Location: VA

    • Total Badges: 36
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 6
Re: MS290 carb adjust after MM
« Reply #6 on: October 28, 2013, 07:16:46 pm »
i feel that the caps help hold the screw in position, as there are no springs on the screws to hold the screw from moving one way or the other. just trim the taps off and put the caps back on like 660 said.
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
MS290 MM

Started by Kenskip1 Stihl

6 Replies
1576 Views 		Last post December 24, 2011, 05:38:54 am
by Al Smith
2 Replies
1255 Views 		Last post August 10, 2012, 04:17:28 pm
by mweba
6 Replies
1544 Views 		Last post April 26, 2013, 01:54:02 pm
by Vance in AK
2 Replies
1448 Views 		Last post April 24, 2013, 09:55:29 pm
by Adirondackstihl
ms290

Started by gunrac « 1 2 3 » Stihl

28 Replies
3324 Views 		Last post February 24, 2014, 01:39:48 pm
by Cut4fun
9 Replies
1974 Views 		Last post May 17, 2014, 11:06:56 pm
by Jason K
3 Replies
1887 Views 		Last post August 15, 2014, 11:59:14 am
by Cut4fun
6 Replies
2308 Views 		Last post November 02, 2015, 07:43:33 pm
by Al Smith
15 Replies
1522 Views 		Last post May 28, 2020, 10:39:55 am
by Cut4fun .
5 Replies
1443 Views 		Last post May 10, 2022, 11:29:50 am
by 3000 FPS