Author Topic: Poulan Poulan Pro bars - OEM & Oregon  (Read 707 times)

0 Members and 0 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2037
  • Karma: 199
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan Poulan Pro bars - OEM & Oregon
« Reply #20 on: November 02, 2015, 04:10:30 am »
I think I know what saw that bar is going on... 8)
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 18130
  • Karma: 342
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan Poulan Pro bars - OEM & Oregon
« Reply #21 on: November 02, 2015, 07:42:59 am »
I think I know what saw that bar is going on... 8)

That PP380 you went through for him. I bet.  ;)
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2037
  • Karma: 199
  • Magnesium and Iron.
  • Location: Northern California.
Re: Poulan Poulan Pro bars - OEM & Oregon
« Reply #22 on: November 02, 2015, 03:28:15 pm »
I think I know what saw that bar is going on... 8)

That PP380 you went through for him. I bet.  ;)

That's what I'm thinking.  The 20" laminate bar that came to me with it when the saw was shipped was completely trashed.  Didn't even bother sending it on with the saw....
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 18130
  • Karma: 342
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Poulan Poulan Pro bars - OEM & Oregon
« Reply #23 on: November 02, 2015, 04:36:50 pm »
I couldnt believe I had a poulan sprocket nose replaceable 20" K041 mount here. I told him I didnt have one and low and behold I came across one. Not a clue where it came from.
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
Poulan 475

Started by Cut4fun « 1 2 ... 31 32 » Poulan

317 Replies
7936 Views
Last post August 28, 2017, 12:24:35 pm
by Cut4fun .
Poulan 415

Started by Cut4fun « 1 2 3 4 5 » Poulan

49 Replies
1967 Views
Last post April 16, 2017, 08:51:19 pm
by Cut4fun .
Poulan 220

Started by Cut4fun . « 1 2 » Poulan

17 Replies
697 Views
Last post June 17, 2017, 12:25:32 pm
by Cut4fun .
Poulan 365

Started by Cut4fun « 1 2 ... 16 17 » Poulan

162 Replies
4407 Views
Last post January 24, 2017, 06:31:28 pm
by Eccentric
Poulan pro 236

Started by Cut4fun . « 1 2 3 4 5 » Poulan

49 Replies
1395 Views
Last post April 28, 2016, 01:03:08 pm
by Cut4fun .
4 Replies
341 Views
Last post November 23, 2012, 12:28:15 am
by Andyshine77
Poulan Bars OEM

Started by Cut4fun . « 1 2 » Poulan

12 Replies
317 Views
Last post December 11, 2012, 05:12:57 pm
by Cut4fun .
0 Replies
319 Views
Last post October 12, 2015, 10:41:19 am
by chainsawlady
4 Replies
115 Views
Last post November 15, 2015, 10:19:28 am
by SDB777
2 Replies
94 Views
Last post May 21, 2017, 08:59:45 pm
by Cut4fun .