« previous next »
Pages: [1]   Go Down

Author Topic: Oregon bars  (Read 2209 times)

0 Members and 11 Guests are viewing this topic.

Offline

  • 6 cube
  • ****
  • Posts: 191
  • Karma: 14
  • Hobby Sawyer
  • Location: Cabot, Arkansas
    • www.slabsblanksandboards.com

    • Total Badges: 24
    Badges: (View All)
    Third year Anniversary Second year Anniversary Poll Voter Level 5 100 Posts One year Anniversary
Oregon bars
« on: November 14, 2015, 06:13:29 pm »
Was wondering if anyone else has experienced abnormal wear on newer bars?

I recently picked up another 22" for the 2186 and have only put two tanks on the bar....  and it's already looking like I have 5 years worth of hard running on it!


Just checking....





Scott (maybe the metal isn't tempered correctly) B
Logged
Jonsered 2186
Jonsered 2094
Stihl MS250
Stihl 064
WoodMizer LT-28

www.slabsblanksandboards.com

Share on Bluesky Share on Facebook

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171

    • Total Badges: 31
    Badges: (View All)
    Level 6 Sixth year Anniversary Fifth year Anniversary 1000 Posts Fourth year Anniversary 500 Posts
Re: Oregon bars
« Reply #1 on: November 14, 2015, 06:30:56 pm »
Oregon is a crapshoot for rail hardness.
Logged

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

    • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: Oregon bars
« Reply #2 on: November 14, 2015, 06:46:28 pm »
We had a run of bad power match bars as well as about a dozen sprocket failures.   Oregon rep came out to one of our job sites to make sure WE weren't the problem.   Burned up a brand new tip in one tank.  Rep was at a loss...
Logged

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24887
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Oregon bars
« Reply #3 on: November 14, 2015, 06:54:11 pm »
Wow good to know this Adam.

Thanks for bringing it up Scott.
Logged

Offline

  • 6 cube
  • ****
  • Posts: 191
  • Karma: 14
  • Hobby Sawyer
  • Location: Cabot, Arkansas
    • www.slabsblanksandboards.com

    • Total Badges: 24
    Badges: (View All)
    Third year Anniversary Second year Anniversary Poll Voter Level 5 100 Posts One year Anniversary
Re: Oregon bars
« Reply #4 on: November 15, 2015, 10:19:28 am »
Whew, it isn't just me then....not that I'd wish problems on anyone else.

Guess I'll need to re-think bar selection once this one is completely toast.  Is there anyway to 'harden rails' for the do it yourself fella?  Heat treatment perhaps?



Scott (like the less expensive bars) B
Logged
Jonsered 2186
Jonsered 2094
Stihl MS250
Stihl 064
WoodMizer LT-28

www.slabsblanksandboards.com
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
1 Replies
2049 Views 		Last post March 20, 2011, 08:33:14 pm
by Cut4fun .
Bow Bars

Started by jmester « 1 2 » Stihl

15 Replies
6092 Views 		Last post July 22, 2012, 10:36:25 am
by jmester
23 Replies
19573 Views 		Last post November 02, 2015, 04:36:50 pm
by Cut4fun .
6 Replies
18394 Views 		Last post November 08, 2014, 09:59:01 pm
by Cut4fun .
21 Replies
52437 Views 		Last post September 17, 2015, 02:51:52 pm
by Cut4fun .
0 Replies
1192 Views 		Last post October 12, 2015, 10:41:19 am
by chainsawlady
5 Replies
21188 Views 		Last post April 15, 2016, 09:09:13 pm
by SawTroll
5 Replies
3120 Views 		Last post January 02, 2018, 07:30:56 am
by Cut4fun .
7 Replies
2665 Views 		Last post February 23, 2018, 01:45:20 pm
by Cut4fun .
4 Replies
2461 Views 		Last post December 30, 2023, 09:05:33 am
by old 040