« previous next »
Pages: 1 ... 8 9 10 11 12 [13] 14 15 16 17   Go Down

Author Topic: Welding Chainsaw Parts  (Read 22134 times)

0 Members and 41 Guests are viewing this topic.

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

    • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: Welding Chainsaw Parts
« Reply #120 on: November 05, 2015, 01:10:28 pm »
[img http:///img]



044 bar plate repair. Owner of this saw had a real issue with throwing chains. Cut al the way into the adjuster pocket and the bar plate area wasn't flat anymore.
Logged

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

    • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: Welding Chainsaw Parts
« Reply #121 on: November 05, 2015, 01:15:27 pm »
[img http:///img]



Ground down to clean metal, then "sweated" out some of the oil soaked area with Mapp gas then cleaned with solvent. Still very dirty! Lol
Logged
Like Like x 1 View List

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Welding Chainsaw Parts
« Reply #122 on: November 05, 2015, 02:01:36 pm »
Havent seen one that chewed up yet. Nice work.
Logged

Offline

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4709
  • Karma: 320
  • Location: Carpenter, Wyoming

    • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Welding Chainsaw Parts
« Reply #123 on: November 05, 2015, 02:20:29 pm »
Looks good Adam.   It sure was chewed up.   
Looks like you took the raised portion the bar sat on down level also.   Are you going to just use a spacer for it.
Logged
PP 505, 475, 445.

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

    • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: Welding Chainsaw Parts
« Reply #124 on: November 05, 2015, 04:42:35 pm »
Saw was a mess ,Oregon faller saw.

Only took. .001-.002 off so it won't be a problem with alignment.
Logged

Offline

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4709
  • Karma: 320
  • Location: Carpenter, Wyoming

    • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Welding Chainsaw Parts
« Reply #125 on: November 05, 2015, 06:30:38 pm »
Quote from: aclarke on November 05, 2015, 04:42:35 pm
Saw was a mess ,Oregon faller saw.

Only took. .001-.002 off so it won't be a problem with alignment.


I gotcha now I was looking at it wrong before.   
Logged
PP 505, 475, 445.

Offline

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24888
  • Karma: 665
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Welding Chainsaw Parts
« Reply #126 on: May 07, 2016, 08:19:34 am »
Quote from: Cut4fun on October 18, 2012, 04:49:21 pm
Quote from: 3000 FPS on October 18, 2012, 04:13:23 pm
Oh I am sure I could do those on my Tig welder.   If you would like it is not a problem.
Roger

I bet you could too.

 Jacks shows they are still for sale and not NLA like I thought.

Out of curiosity I went to Jacks small engines and I can still get new for $5 a piece  8) 8). I guess I will just add some to my next big order to absorb the $7.99 shipping.   PN# 503424101    SPUR  $5.00   


They are NLA now. Just to update.
Logged
Informative Informative x 1 View List

Offline

  • 6 cube
  • ****
  • Posts: 178
  • Karma: 24
  • Location: Yokohama, JAPAN

    • Total Badges: 17
    Badges: (View All)
    One year Anniversary Level 4 100 Posts Signature 50 Posts Linux User
Re: Welding Chainsaw Parts
« Reply #127 on: July 17, 2017, 08:14:45 am »
Quote from: 3000 FPS on October 27, 2012, 10:11:19 pm
For those of you who may interested in welding this is an 8500 crankcase hit by a chain.  I wanted to show this because it can demonstrate how an edge can be built back up by using a material behind it that will not stick to the magnesium while welding. If you do not do this with thin castings such as on this saw it will just fall away when the puddle forms.

Quote from: 3000 FPS on October 28, 2012, 02:45:13 pm
So here is the second part of welding on the 8500 case.   You can see in the before and after pictures that there was a bow on this saw at one time.   I wanted to make look like it never existed.   This was done with a backing material and just ran a bead along the edge unitl it I got it built up.  I did this from both sides so that there would be enough material to shape when done welding.

Good evening Roger, could you give me a couple of tips on there,

one:
what kind of material is that you are using for this backing? 

two:
what kind of magnesium filler do you use for them, one of the member her Srcarr52 says he is using AZ92A filler for Solo twin cover in his video.

Thanks in ahead,
Chy

Logged

(McCulloch) PM6,PM320,SP40,PM484,10-10A,PM610,35A,47,300,450,PM800,1-70,1-80,740,740(mod),795,SP125C
(Echo) CS-302,CS-502EVL,CS-60S,CS-601S VL,CS-803EVL,CS-803EVL(mod),CS-651T
(Homelite) DM 50,Super Mini S,Super XL-9225,Super 1050
(Partner) 1614/Mini P,R417T,S55,R14T,R12,R12,K12S,
(Stihl) MS-180C,08S,070AV,084AV
(Shindaiwa) Pecker A110,E305AV
(Dolmar) 123,PS 7900
(Jonsereds) 49SP,455
(Husqvarna) 550XP
(Tanaka) TCS-33EDTP
(Makita) EK-900
(Alpina) A40
Useful Useful x 1 View List

Offline

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4709
  • Karma: 320
  • Location: Carpenter, Wyoming

    • Total Badges: 43
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 7 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary
Re: Welding Chainsaw Parts
« Reply #128 on: July 17, 2017, 09:43:24 am »
Yes AZ92A is the same filler that I use on all the magnesium chainsaw parts I have welded.

For a backing I use any kind of metal that the magnesium will not stick to.   I have used some mild steel and some sheet metal.   I have also used a steel rod.   
Logged
PP 505, 475, 445.
Informative Informative x 2 View List

Offline

  • 6 cube
  • ****
  • Posts: 178
  • Karma: 24
  • Location: Yokohama, JAPAN

    • Total Badges: 17
    Badges: (View All)
    One year Anniversary Level 4 100 Posts Signature 50 Posts Linux User
Re: Welding Chainsaw Parts
« Reply #129 on: July 18, 2017, 01:17:25 am »
Quote from: 3000 FPS on July 17, 2017, 09:43:24 am
Yes AZ92A is the same filler that I use on all the magnesium chainsaw parts I have welded.

For a backing I use any kind of metal that the magnesium will not stick to.   I have used some mild steel and some sheet metal.   I have also used a steel rod.   
Thanks Roger, placing a backing plate sounds very nice to me. Will have a try on this method. Also appreciate this information on the filler. Will make some report when I made some try.
Chy
Logged

(McCulloch) PM6,PM320,SP40,PM484,10-10A,PM610,35A,47,300,450,PM800,1-70,1-80,740,740(mod),795,SP125C
(Echo) CS-302,CS-502EVL,CS-60S,CS-601S VL,CS-803EVL,CS-803EVL(mod),CS-651T
(Homelite) DM 50,Super Mini S,Super XL-9225,Super 1050
(Partner) 1614/Mini P,R417T,S55,R14T,R12,R12,K12S,
(Stihl) MS-180C,08S,070AV,084AV
(Shindaiwa) Pecker A110,E305AV
(Dolmar) 123,PS 7900
(Jonsereds) 49SP,455
(Husqvarna) 550XP
(Tanaka) TCS-33EDTP
(Makita) EK-900
(Alpina) A40
Like Like x 1 View List
Pages: 1 ... 8 9 10 11 12 [13] 14 15 16 17   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
0 Replies
1612 Views 		Last post April 19, 2012, 10:08:34 am
by tommysp61
3 Replies
2985 Views 		Last post June 07, 2012, 02:47:11 pm
by Dh1984
2 Replies
3048 Views 		Last post February 08, 2013, 10:51:18 pm
by mattinky
0 Replies
897 Views 		Last post December 02, 2013, 10:34:35 am
by Forester Parts
5 Replies
4212 Views 		Last post February 08, 2018, 08:28:16 pm
by Al Smith
3 Replies
3211 Views 		Last post November 05, 2015, 12:02:37 pm
by Cut4fun .
8 Replies
3343 Views 		Last post April 29, 2016, 11:47:09 am
by chy_farm
0 Replies
2006 Views 		Last post December 05, 2015, 10:17:42 am
by Cut4fun .
1 Replies
2336 Views 		Last post April 06, 2016, 04:17:50 pm
by aclarke
3 Replies
5091 Views 		Last post May 06, 2020, 09:13:40 am
by Al Smith