« previous next »
Pages: [1] 2 3   Go Down

Author Topic: Sachs Dolmar 143 info?  (Read 7935 times)

0 Members and 51 Guests are viewing this topic.

Offline

  • 5 cube
  • ***
  • Posts: 90
  • Karma: 8

    • Total Badges: 17
    Badges: (View All)
    Second year Anniversary Level 4 One year Anniversary 50 Posts Poll Voter 10 Posts
Sachs Dolmar 143 info?
« on: December 12, 2013, 08:37:11 pm »
I have a chance to get a Sachs Dolmar 143 on  a trade and I was wondering if anyone can tell me some specs on the Sachs Dolmar 143. Basically Just wonder if it would make a good cookie cutter

Cut4fun its the same saw I sent you the link to. A friend of mine bought it today I have not seen it yet but said it has lots of compression and it starts and stalls.
Logged

Share on Bluesky Share on Facebook

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: Sachs Dolmar 143 info?
« Reply #1 on: December 12, 2013, 08:50:45 pm »
Model Profile: 143
acresinternet.com
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • 5 cube
  • ***
  • Posts: 90
  • Karma: 8

    • Total Badges: 17
    Badges: (View All)
    Second year Anniversary Level 4 One year Anniversary 50 Posts Poll Voter 10 Posts
Re: Sachs Dolmar 143 info?
« Reply #2 on: December 12, 2013, 09:06:53 pm »
Thanks for the link. looks its a heavy saw compared t what im used to
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: Sachs Dolmar 143 info?
« Reply #3 on: December 12, 2013, 10:03:27 pm »
Its 95cc old school. May run a lower RPM than a 066 but have a lot of torque? Don't rule out a 8 Pin rim?

Cut4fun had a old Echo 70cc class saw monster that he wanted to run against my Dolmar 6800. The Echo had a 8 pin rim. It was noticeable that the Echo was a low rpm engine and the Dolmar 6800 turned more like 9000 in the cut with a 7 pin rim. Though the Echo sounded much slower, both saws were practically the same speed in the cut.

Just keep that in mind when comparing like the Sachs Dolmar 143 with a 066 Stihl which are both about the same size.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • 5 cube
  • ***
  • Posts: 90
  • Karma: 8

    • Total Badges: 17
    Badges: (View All)
    Second year Anniversary Level 4 One year Anniversary 50 Posts Poll Voter 10 Posts
Re: Sachs Dolmar 143 info?
« Reply #4 on: December 17, 2013, 06:15:15 pm »
Anybody want to give me some secrets on some mods for this saw? It has an 8 tooth sprocket on it now and there seems be no end to power. I tried it out in a big block of rock maple yesterday and it really surprised me. But I want more power/speed  ;D

would it make a good race saw? the race i go to we are all amateurs  in a friends back yard nothing to serious
Logged

Offline

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO

    • Total Badges: 39
    Badges: (View All)
    Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary 5000 Posts Third year Anniversary
Re: Sachs Dolmar 143 info?
« Reply #5 on: December 17, 2013, 08:18:50 pm »
Cut4fun back in his chainsaw race days would video his log cuts and then stopwatch the videos to see how he was doing with his changes.

Some of the technique is in your performance. You got to hit the log where you want to and cut straight.

More of the technique is the chain. It has to be sharp with an aggressive hook. The last sharpening on a old chain cuts the best.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline

  • 6 cube
  • ****
  • Posts: 160
  • Karma: 16
  • Location: Valley Center,KS

    • Total Badges: 21
    Badges: (View All)
    Level 5 Poll Voter Second year Anniversary 100 Posts 50 Posts Level 4
Re: Sachs Dolmar 143 info?
« Reply #6 on: December 18, 2013, 04:50:55 am »
I have a strong running 143 as well and have ran a 10pin sprocket on it just to play and it pulled it just fine. What spec of chain will you be running? Also almost no one makes bars for these anymore but large mount stihl (above 066,660 or 14mm slot) will fit.
Logged
Trapped in time, surrounded by evil, low on gas

Offline

  • 6 cube
  • ****
  • Posts: 160
  • Karma: 16
  • Location: Valley Center,KS

    • Total Badges: 21
    Badges: (View All)
    Level 5 Poll Voter Second year Anniversary 100 Posts 50 Posts Level 4
Re: Sachs Dolmar 143 info?
« Reply #7 on: December 18, 2013, 09:09:47 am »
Has anybody ever tried to "soup" up one of these? At only 1hp sae less than the 166 and many lbs lighter this saw looks to have a more impressive power/weight ratio than the 166. I wish that mine had a compression release because it can hurt if you don't get a good grip!
Logged
Trapped in time, surrounded by evil, low on gas

Offline

  • 4 cube
  • **
  • Posts: 41
  • Karma: 7
  • Location: Menlo Park, CA

    • Total Badges: 22
    Badges: (View All)
    Level 5 Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary
Re: Sachs Dolmar 143 info?
« Reply #8 on: January 11, 2014, 05:59:26 pm »
The 143 has 95cc and for sure is a beast. As handy as a Dolmar 133, this is almost 100cc-class!
The power cutter type 343 has the same basis, I repaired and tested one of these recently.

However, the crank is the same as in the 133 super. And the 133 super  is basically an ordinary 133 with a different piston and slightly higher compression.
While the 143 beeing somehow the "dual-pimped" Dolmar 133, at least back home in Germany a few crank-failures have been reported due to fatigue of material! (The 133 super/143 crank is actually different from the ordinary 133-crank because they switched to roller bearings at that time, with a different clearance on the crank. The main bearing of the rod is basically the same)

The 143 is one of the saws I would inspect very carefully when making a trade, just checking for not having a scored piston might not be enough. And the lower hours the better.


edit: ups, just found that you already got it, http://chainsawrepair.createaforum.com/dolmar/sach-dolmar-143-chain-brake-help/, good luck!  8)
Logged

Offline

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania

    • Total Badges: 31
    Badges: (View All)
    Level 6 Fourth year Anniversary Spammer 25 Posts in one day Karma Good 1000 Posts Third year Anniversary
Re: Sachs Dolmar 143 info?
« Reply #9 on: May 27, 2014, 05:18:25 pm »
Logged
Ron
Pages: [1] 2 3   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
Sachs Dolmar 166

Started by Cut4fun « 1 2 ... 5 6 » Dolmar Makita

57 Replies
15113 Views 		Last post July 24, 2026, 08:45:42 am
by Cut4fun .
7 Replies
4224 Views 		Last post January 02, 2012, 07:10:50 pm
by rms61moparman
3 Replies
1638 Views 		Last post December 07, 2013, 08:57:42 pm
by chainsman1
2 Replies
1796 Views 		Last post May 18, 2013, 11:56:08 pm
by adam32
8 Replies
3031 Views 		Last post August 26, 2014, 12:14:10 am
by stihls066
0 Replies
1251 Views 		Last post April 12, 2014, 12:28:35 am
by stihls066
49 Replies
16961 Views 		Last post March 24, 2024, 09:21:38 am
by Cut4fun .
0 Replies
1120 Views 		Last post August 10, 2015, 02:17:30 pm
by stihls066
12 Replies
5621 Views 		Last post June 25, 2017, 10:13:52 am
by Cut4fun .
2 Replies
2376 Views 		Last post January 27, 2017, 06:51:49 pm
by 166